Graco Ultimate Mx1095 Скачать руководство пользователя страница 22

Страница: 22 / 22

309255

Technical Data

Model

100–120V,

∅

, A, Hz

220–240V,

∅

, A, Hz

Generator
Minimum
W

Motor
HP (W)

Cycles per
gallon (liter)

Maximum
Delivery
gpm (lpm)

Maximum
Tip size

Fluid
Outlet
npsm

1 gun

2 guns

695

1, 15,
50/60

1, 10,
50/60

3000

0.9 (373)

566 (150)

0.6 (2.3)

0.026

N/A

1/4 in.

795

1, 15,
50/60

1, 10,
50/60

4000

1.0 (466)

244 (64.6)

0.8 (3.0)

0.028

0.019

1/4 in

1095

1, 15/20,
50/60

1, 10,
50/60

4000

1.2 (560)

200 (53)

1.1 (3.8)

0.032

0.021

1/4 in

Basic Sprayer Wetted Parts: . . . . . . . . . . . . . . . . . . . . . . . . . . . .

zinc-plated carbon steel, polyurethane, polyethylene,
stainless steel, PTFE, Delrin

chrome plating, leath-

er, V-Max

UHMWPE, aluminum, stainless steel,

tungsten carbide

NOTE:

Delrin

is a registered trademarks of the DuPont Co.

Dimensions

Model

Style

Weight lb (kg)

Height in. (cm)

Width in. (cm)

Length in. (cm)

695

Hi–Boy

87 (39)

30 (76)

22.5 (57)

25.5 (65)

Lo–Boy

78 (35)

22 (56)

19.5 (49.5)

27 (69)

795

Hi–Boy

107 (48.5)

30 (76)

20.5 (52.1)

28 (71)

Lo–Boy

101 (46)

22 (56)

22.5 (57)

27 (69)

1095

Hi–Boy

120 (54)

30 (76)

22.5 (57)

29 (74)

Graco Phone Number

TO PLACE AN ORDER OR FOR SERVICE

, contact your Graco distributor,

or call 1–800–690–2894 to identify the nearest distributor.

All written and visual data contained in this document reflect the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

mm 309255

This manual contains English

Graco Headquarters:

Minneapolis

International Offices:

Belgium, Korea, China, Japan

GRACO INC.

P.O. BOX 1441

MINNEAPOLIS, MN

55440–1441

www.graco.com

PRINTED IN U.S.A. 1/2001, Rev 11/2005

Содержание Ultimate Mx1095























Результаты поиска

Содержание Ultimate Mx1095

Отзывы:

Похожие инструкции для Ultimate Mx1095

Бренды по названию

Популярные бренды

Graco Ultimate Mx1095, Инструкции по ремонту

Результаты поиска

Содержание Ultimate Mx1095

Отзывы:

Похожие инструкции для Ultimate Mx1095

Бренды по названию

Популярные бренды