manualshive.com logo in svg

Graco TrueCoat Plus, Операция

Поделиться
Скачать
Graco TrueCoat Plus Скачать руководство пользователя страница 18

Troubleshooting 

18

3A0705B

Troubleshooting

Check everything in this Troubleshooting Table before 
you bring the sprayer to an authorized service center.

Problem

Cause

Solution

Sprayer makes no sound when 
trigger is pulled

Trigger is locked.

Disengage trigger lock. See page 6.

Status Indicator Light is solid RED 
when triggering, indicating that the 
battery charge is low.

Replace with charged battery and 
place old battery in charger.

Status Indicator Light is flashing RED 
when triggering, indicating that the 
battery is too hot to operate.

Allow battery to cool.

Status Indicator Light does not light 
when sprayer is triggered.

Battery is not installed or is 
damaged.

Sprayer makes sound but no material 
is sprayed when trigger is pulled

Sprayer is not primed.

Prime the pump. See 

Starting a new 

Job (or Refilling the Cup)

, page 10.

Prime/relief valve is in UP position.

Pull valve DOWN to spray position.

Suction Tube is missing or improperly 
installed.

Make sure Suction Tube is properly 
installed.

Inlet valve is stuck from material 
residue left in sprayer.

Use a pencil or thin rod to lightly push 
on inlet valve to make sure it moves 
up and down freely. See 

Starting a 

new Job (or Refilling the Cup)

, 

page 10.

Tip is not in SPRAY position.

Turn tip to SPRAY position.

Tip is clogged.

See 

Unclogging Tip/Guard 

Assembly

, page 13.

Suction Tube screen is clogged.

See 

Shutdown and Cleaning

, page 

14. 

Sprayer has been tilted too far and 
suction tube has lost contact with 
material.

Make sure cup is filled with material. 
Do not tilt the cup too far. Prime the 
pump. See 

Starting a new Job (or 

Refilling the Cup)

, page 10.

No or low material in cup.

Refill cup with material.

Tip filter is clogged.

Remove and clean tip filter. See 

Unclogging Tip/Guard Assembly

, 

page 13.

Fine Finish Optimizer is installed 
while using an incompatible material.

Make sure compatible material is 
being used. See 

Reversible Tip 

Selection Chart

, page 11.

Suction Tube o-rings are damaged or 
missing.

Replace Suction Tube and o-rings.

Sprayer has reached maximum life.

Replace sprayer.

Material is leaking from hole in front 
of sprayer.

Replace sprayer.

Содержание TrueCoat Plus

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды