background image

3

310530

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious
injury or death if you do not follow the corresponding
instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
corresponding instructions.

WARNING

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and
result in serious injury.

D

This equipment is for professional use only.

D

Read all instruction manuals, warnings, tags, and labels before operating the equipment.

D

Use the equipment only for its intended purpose.

D

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

D

Check the equipment daily. Repair or replace worn or damaged parts immediately.

D

Never exceed the recommended working pressure or the maximum air inlet pressure stated on
your pump or in the 

Technical Data

 on page 33.

D

Be sure that all spray/dispensing equipment and accessories are rated to withstand the maxi-
mum working pressure of the pump. Do not exceed the maximum working pressure of any
component or accessory used in the system.

D

Use fluids and solvents that are chemically compatible with the equipment wetted parts.  See
the 

Technical Data

 sections of all the equipment manuals. Always read the material manufac-

turer’s literature before using fluid or solvent in this pump.

D

Always wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid
and solvent manufacturers.

D

Wear hearing protection when operating this equipment.

D

Comply with all applicable local, state and national fire, electrical and other safety regulations.

HOT SURFACE AND FLUID HAZARD

Heated fluid can cause severe burns and can cause equipment surfaces to become very hot.

D

Wear protective gloves and clothing when operating this equipment in a heated system.

D

Do not touch the metal heat sink when the surface is hot.

D

Allow the equipment to cool thoroughly before servicing.

Содержание Therm-O-Flow C03509



































Отзывы: