Graco Therm-O-Flow 200 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 109

Graco Therm-O-Flow 200 Скачать руководство пользователя страница 57

Update

Update

Update Software

Software

Software

When software is updated on the ADM the software
is then automatically updated on all connected
GCA components. A status screen is shown while
software is updating to indicate progress.

1.

Turn system main power switch OFF.

2.

Remove ADM from bracket.

3.

Remove token access panel.

4.

Insert and press software upgrade token (T)
firmly into slot.

Note

There is no preferred orientation of token

T

5.

Install ADM into bracket.

6.

Turn system main power switch ON.

NOTICE

NOTICE

NOTICE

A status is shown while software is updating to
indicate progress. To prevent corrupting the
software load, do not remove token until the
status screen disappears.

Note

When the screen turns on, you will see
the following screens:

First:

First:

First:

Software is checking
which GCA modules
will take the available
updates.

Second:

Second:

Second:

Status of the update
with approximate time
until completion.

Third:

Third:

Third:

Updates are
complete. Icon
indicates update
success/failure. See
the following Icon
table.

Icon

Icon

Icon

Description

Description

Description

Update successful.

Update unsuccessful.

Update complete, no
changes necessary.

Update was
successful/complete
but one or more HCA
modules did not have
a CAN boot-loader
so software was
not updated on that
module.

334130D

57

«
...
55
56
57
58
59
...
»

Содержание Therm-O-Flow 200














































































































Отзывы:

Нет отзывов