manualshive.com logo in svg

Graco Spindl-Gard 24B219, Инструкция по эксплуатации, Страница: 6 / 14

Поделиться
Скачать
Graco Spindl-Gard 24B219 Скачать руководство пользователя страница 6

Installation 

6

313444E

Timer Models Only

5. Connect input power leads to the input terminal 

block (Terminals 4 and 6) (F

IG

. 2).

All Models

6. Replace electrical enclosure cover.

Pneumatic Connections

Pressure Relief Procedure

1. Loosen the purge plug (A) on the air/oil mixing block 

assembly (K).

2. Press the manual run button (B) until oil flows out of 

the port.

Connecting Pneumatic Fittings - All models

NOTE:

•

Incoming air should be dry (40°F, 4.4°C) and be fil-
tered to 5 micron.

•

Minimum inside diameter of incoming air line should 
be 0.25 inch (0.63 cm).

1. Connect incoming air line to the 1/4-18 NPSF inlet 

(F).

2. Connect air/oil delivery line from the air/oil mixing 

block (K) to the bearing point.

Air Flow Data Chart

The tube size from the air/oil mixing block (K) to the bearing is critical for proper air and oil delivery to the bearings. 
Refer to the Air Flow Chart (below) for orifice and corresponding delivery tube sizes and the resulting airflow.

F

IG

. 2

Orifice Size 

Inches (mm)

Delivery Tube 

O.D. 

Inches (mm)

Delivery Tube 

I.D. 

Inches (mm)

Air Flow @30 psi 

SCFM (LPM)

Air Flow @ 60 psi 

SCFM (LMP)

0.030 (0.76) 

3/16 (5)

1/8 (3)

16.1 (0.570)

25.2 (0.890)

0.040 (1.00) 

1/4 (6)

3/16 (5)

27.7 (0.980)

45.2 (1.600)

0.050 (1.27)

5/16 (7)

1/4 (6)

48.4 (1.710)

81.5 (2.880)

0.060 (1.52) 

5/16 (7)

1/4 (6)

103.7 (2.180)

103.9 (3.670)

Содержание Spindl-Gard 24B219















Отзывы:

Нет отзывов