Graco SD 10 Series Скачать руководство пользователя страница 12

Страница: 12 / 54

Installation

3A8626A

All Models

Select the reel bank mounting location (F

. 7).

• For high ceilings, suspend a suitable support

structure for the reels, so the hoses will be long

enough to reach the service area.

• A reel bank mounted in a one-lift service bay should

be at least 6 ft (1.9 m) from the center line of the lift.

• A reel bank mounted in a two-lift service bay should

be mounted an equal distance between the lifts.

• A bank of all motor oil reels should be mounted

about 5 ft (1.5 m) from the center of the lift, toward

the front of the lift rails.

SD or XD Models Only

NOTE: The reference letters in the following instructions

refer to F

. 8 and F

. 26.

1. Determine if the position of the roller guide arm (a)

. 8) is in the desired installation position. If it is

not in the desired installation position, skip to Step

The hose reel is factory-assembled and shipped

with the roller guide arm (a) in either the AA or EE

position (F

. 8).

. 7

6 ft (1.9 m) minimum for one (1) lift

Center between two lifts

5 ft (1.5 m) minimum for motor oil

. 8

AA Shipping Position

EE Shipping Position

AA*

EE**

*SD Models without an H or J in the fifth number

position of the model number are shipped with the

roller guide arm (a) in the AA position.

**SD Models with an H or J in the fifth number position

of the model number are shipped with the roller guide

arm (a) in the EE position.

**All XD Models are shipped with the roller guide arm

(a) in the EE position.

Содержание SD 10 Series























































Результаты поиска

Содержание SD 10 Series

Отзывы:

Бренды по названию

Популярные бренды

Graco SD 10 Series, Руководство пользователя

Результаты поиска

Содержание SD 10 Series

Отзывы:

Бренды по названию

Популярные бренды