background image

Priming Piston Service

Priming Piston Service

Disconnect the Pump

WARNING

PRESSURIZED FLUID HAZARD
This equipment stays pressurized until pressure is

relieved manually. To help prevent serious injury

from moving parts, or from pressurized fluid, such

as splashing in the eyes or on skin, follow the

Pressure Relief Procedure in your system manual

when you stop pumping and before you clean,

check, or service the equipment.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when

in the work area to help prevent serious injury,

including eye injury, hearing loss, or inhalation of

toxic fumes.

This procedure involves thoroughly disassembling

and cleaning the individual parts in the pump lower

unit. Prior to performing this procedure, flush the

pump and relieve pressure as described in the

system manuals, disconnect all hoses, and remove

the pump from the system.
1. Release the upper clamp (123) holding the

displacement pump to the tie rod plate (122).

2. Slide the pump down from the air motor. Tilt the

pump and pull the displacement rod (117) out of

the coupler (C). Remove the gasket (102).

Note: Be careful not to scratch the displacement

rod.

Figure 1 Remove displacement pump.

Disassemble the Pump

Note: Pump Repair Kit 24G550 is available.

Purchase the kit separately. Kit parts are

marked with an * in the parts section. See

Priming Piston Displacement Pump Model 25M906,

25M906C31, page 9

.

1. Remove the retaining pin (116) from the

connecting rod (109). Slide off the priming piston

(108).

2. Release the lower clamp (123) to remove the

intake valve housing (107) from the pump

cylinder (101). Remove the gasket (102).

3. Remove the poppet (114), spring (113), and

valve stop (111) off the connecting rod (109).

4. Remove the bearing (112) from the center of the

valve stop (111).

5. Remove the packings (115) from the center of

the poppet (114).

Figure 2 Remove priming piston.

6. Push the displacement rod (117) out through the

bottom of the cylinder (101).

3A5564A

5

Содержание SaniForce















Отзывы: