Graco S2550 Скачать руководство пользователя

Страница: 32 / 56

Troubleshooting

3A4203B

Sprayer does not run at all

AND

Display shows E=04

Control board status light blinks 4

times repeatedly

Check voltage supply to the sprayer

(control board is detecting a multiple

voltage surges).

Turn ON/OFF switch

OFF

and

disconnect power to sprayer.
Locate a good voltage supply to

prevent damage to electronics.

Sprayer does not run at all

AND

Display shows E=05

Control board status light blinks 5

times repeatedly

Control is commanding motor to run

but motor shaft does not rotate.

Possibly locked rotor condition, an

open connection exists between

motor and control, there is a problem

with motor or control board, or motor

amp draw is excessive.

1.Remove pump and try to run

sprayer. If motor runs, check for

locked or frozen pump or drive train.

If sprayer does not run, continue to

step 2.

2.Turn ON/OFF switch

OFF

and

disconnect power to sprayer.

3.Disconnect motor connector(s) from

control board socket(s). Check that

motor connector and control board

contacts are clean and secure. If

contacts are clean and secure,

continue to step 4.

4.Connect a DC voltmeter across the

two motor wires – red & black spin

the motor fan and check for a

voltage to register on the meter. If

voltage is not present, check

brushes. If OK, replace motor. If

voltage is present, go to step 5.

5.Perform a spin test by connecting a

9 –12 Volt battery to the motor

leads. Motor leads may vary in style

and size. Locate the two wires

going to the carbon brushes

normally Red and Black. Motor

should spin when battery is

connected to the motor leads.

Problem

What to Check

How to check

YELLOW

BLACK (-)

9-VOLT

BATTERY

RED (+)

ti24722

Содержание S2550

























































Результаты поиска

Содержание S2550

Отзывы:

Похожие инструкции для S2550

Бренды по названию

Популярные бренды

Graco S2550, Операция - Ремонт - Запчасти

Результаты поиска

Содержание S2550

Отзывы:

Похожие инструкции для S2550

Бренды по названию

Популярные бренды