Graco PRO Auto Xs Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 56

background image

Repair

34

309297K

Air Cap/Nozzle Replacement

1.

Prepare gun for service, page 32.

2.

Remove the retaining ring (1) and air cap (3). See
F

3.

Point gun up while removing the fluid nozzle (4)
assembly with the multi-tool (40).

Fig. 21. Air Cap/Nozzle Replacement

Use non-silicone grease, Part No. 111265, on the small
o-ring (4b). Do not over-lubricate. Do not lubricate the
contact ring (4a).

4.

Lightly lubricate the o-ring (4b). Install it and the
contact ring (4a) on the nozzle (4).

Make sure the electrode needle (7) is finger- tight (page
35).

5.

Install the fluid nozzle (4) with the multi-tool (40).
Tighten until the fluid nozzle seats in the gun barrel
(1/8 to 1/4 turn past hand-tight).

6.

Carefully install the air cap (3). Be sure to insert the
electrode (7) through the center hole of the air cap.
Rotate the air cap to the desired position.

7.

Make sure the u-cup (1a) is in place on the retaining
ring (1). The lips must face forward. Tighten the
retaining ring until the air cap is held firmly in place;
you should not be able to rotate the air cap horns by
hand.

8.

Test gun resistance, page 26.

9.

Install the gun onto the manifold and bracket. See
page 33.

CAUTION

Hold the front end of the gun up and trigger the gun
while removing the nozzle to help drain the gun and
prevent any paint or solvent left in the gun from enter-
ing the air passages.

TI1572A

1, 3

3

4

4a

4b

1

40

4

7

1a

WARNING

Fire, Explosion, and Electric Shock Hazard

The nozzle contact ring (4a) is a conductive
contact ring, not a sealing o-ring. To reduce
the risk of sparking or electric shock, do not
remove the nozzle contact ring (4a) except
to replace it and never operate the gun
without the contact ring in place. Do not
replace the contact ring with anything but a
genuine Graco part.

«
...
32
33
34
35
36
...
»

Содержание PRO Auto Xs Series

























































Отзывы:

Нет отзывов

Похожие инструкции для PRO Auto Xs Series

Бренд: WAGNER Страницы: 68

Бренд: WALTHER PILOT Страницы: 44

Бренд: WAGNER Страницы: 110

Бренд: WAGNER Страницы: 55

Бренд: C.A. Technologies Страницы: 4

Бренд: Hagie Страницы: 276

Бренд: WAGNER Страницы: 32

Бренд: Goizper Group Страницы: 22

Бренд: Ozito Страницы: 2

Бренд: Volpi Страницы: 40

Бренд: Dynalabs Страницы: 13

Бренд: Performance Tool Страницы: 6

Бренд: Larius Страницы: 46

Бренд: Steripower Страницы: 2

Бренд: ASM Страницы: 28

Бренд: Husky Страницы: 24

Diversey IntelliSpray

Бренд: Taski Страницы: 14

Бренд: 3M Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды