Graco PRO Auto Xs Series Скачать руководство пользователя страница 2

Страница: 2 / 56

309297K

Table of Contents

List of Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Warning Symbol . . . . . . . . . . . . . . . . . . . . . . . . . 3

Caution Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

How the Electrostatic Air Spray Gun Works . . . . 6

Operating the Spray Function . . . . . . . . . . . . . . . 6

Operating the Electrostatics . . . . . . . . . . . . . . . . 6

Gun Features and Options . . . . . . . . . . . . . . . . . 6

Changing the kV Setting . . . . . . . . . . . . . . . . . . . 6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Install the System . . . . . . . . . . . . . . . . . . . . . . . . 8

Warning Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Ventilate the Spray Booth . . . . . . . . . . . . . . . . . . 8

Install the Air Line Accessories . . . . . . . . . . . . . 10

Install the Fluid Line Accessories . . . . . . . . . . . 10

Install the Gun and Mounting Bracket . . . . . . . . 10

Connect the Air and Fluid Lines . . . . . . . . . . . . 11

Manifold Connections . . . . . . . . . . . . . . . . . . . . 11

Optional Fiber Optic Cable Connection . . . . . . . 12

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Check Electrical Grounding . . . . . . . . . . . . . . . . 14

Check Fluid Resistivity . . . . . . . . . . . . . . . . . . . 15

Check Fluid Viscosity . . . . . . . . . . . . . . . . . . . . 15

Install the Fabric Cover . . . . . . . . . . . . . . . . . . . 15

245324 HC Conversion Kit . . . . . . . . . . . . . . . . 16

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Pressure Relief Procedure . . . . . . . . . . . . . . . . 17

Operating Checklist . . . . . . . . . . . . . . . . . . . . . . 18

Select a Fluid Nozzle and Air Cap . . . . . . . . . . 18

Adjust the Spray Pattern . . . . . . . . . . . . . . . . . . 19

Adjust the Electrostatics . . . . . . . . . . . . . . . . . . 20

Spraying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Triggering the Fluid Alone . . . . . . . . . . . . . . . . . 21

Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Daily Care and Cleaning . . . . . . . . . . . . . . . . . . 22

Clean the Air Cap and Fluid Nozzle . . . . . . . . . 24

Check for Fluid Leakage . . . . . . . . . . . . . . . . . . 25

Electrical Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Test Gun Resistance . . . . . . . . . . . . . . . . . . . . . 26

Test Power Supply Resistance . . . . . . . . . . . . . 27

Test Electrode Resistance . . . . . . . . . . . . . . . . . 28

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Spray Pattern Troubleshooting . . . . . . . . . . . . . 29

Gun Operation Troubleshooting . . . . . . . . . . . . . 30

Electrical Troubleshooting . . . . . . . . . . . . . . . . . 31

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Prepare the Gun for Service . . . . . . . . . . . . . . . 32

Remove the Gun from the Manifold . . . . . . . . . . 33

Install the Gun on the Manifold . . . . . . . . . . . . . 33

Air Cap/Nozzle Replacement . . . . . . . . . . . . . . 34

Electrode Replacement . . . . . . . . . . . . . . . . . . . 35

Fluid Packing Removal . . . . . . . . . . . . . . . . . . . 36

Packing Rod Repair . . . . . . . . . . . . . . . . . . . . . . 37

Piston Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Adjust the Actuator Arm . . . . . . . . . . . . . . . . . . 39

Barrel Removal . . . . . . . . . . . . . . . . . . . . . . . . . 40

Barrel Installation . . . . . . . . . . . . . . . . . . . . . . . . 41

Power Supply Removal and Replacement . . . . 42

Turbine Alternator Removal and Replacement . 43

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Air Line Accessories . . . . . . . . . . . . . . . . . . . . . 52

Fluid Line Accessories . . . . . . . . . . . . . . . . . . . 52

Miscellaneous Accessories . . . . . . . . . . . . . . . . 53

Gun Accessories . . . . . . . . . . . . . . . . . . . . . . . . 54

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 56

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 56

Содержание PRO Auto Xs Series

























































Результаты поиска

Содержание PRO Auto Xs Series

Отзывы:

Похожие инструкции для PRO Auto Xs Series

Бренды по названию

Популярные бренды

Graco PRO Auto Xs Series, Инструкция-перечень запасных частей

Результаты поиска

Содержание PRO Auto Xs Series

Отзывы:

Похожие инструкции для PRO Auto Xs Series

Бренды по названию

Популярные бренды