manualshive.com logo in svg

Graco PRO 3500WB, Руководство пользователя

Поделиться
Скачать
Graco PRO 3500WB Скачать руководство пользователя страница 23

SPRAY GUN ELECTRICAL TESTS

Test Resistor Stud Resistance

Remove the resistor stud. See 

Air Cap/Nozzle/Resistor

Stud Replacement. Check the resistance between the
black resistor stud contact ring (D) and the needle con-
tact ring (E). Refer to Fig 15.  You may have to press
down on the contact ring (D) in several places to get a
good reading.

The resistance should be 22.5 to 27.5 megohms. If the
resistance is correct, make sure the metal contact (C) in
the barrel and the needle contact wire (E) are clean. If the
resistance is outside the specified range, the resistor is
defective and the resistor stud (22) must be replaced.
See 

Air Cap/Nozzle/Resistor Stud Replacement.

WARNING

The resistor stud contact ring (D) is a conductive
contact ring, NOT a sealing o-ring. To reduce the
risk of sparking, which could cause fire, explosion,
or electrostatic shock and result in serious injury,
DO NOT remove the resistor stud contact ring (D)
from the resistor stud or operate the gun without
the contact ring in place. DO NOT replace the re-
sistor stud with anything but a genuine Graco part.

Fig 15  

KEY

D

Resistor Stud Contact Ring

E

Needle Contact Ring

D

E

0442

Fig 16  

Содержание PRO 3500WB

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды