background image

3

308–333

WARNING

FIRE AND EXPLOSION HAZARD

Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and
result in fire or explosion and serious injury.

Ground the equipment and the object being sprayed. See Grounding on page 4.

If there is any static sparking while using the equipment, stop spraying immediately. Identify and
correct the problem.

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvent or the fluid being
sprayed.

Extinguish all the open flames or pilot lights in the spray area.

Electrically disconnect all the equipment in the spray area.

Keep the spray area free of debris, including solvent, rags, and gasoline.

Do not turn on or off any light switch in the spray area while operating or if fumes are present.

Do not smoke in the spray area.

Do not operate a gasoline engine in the spray area.

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

This equipment is for professional use only.

Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check the equipment daily. Repair or replace worn or damaged parts immediately.

Do not exceed the maximum working pressure of the lowest rated system component. This equip-
ment has a 3600 psi (25.0 MPa, 250 bar) maximum fluid working pressure at 120 psi (0.83
MPa, 8.3) maximum air inlet pressure
.

Do not lift pressurized equipment.

Use only Graco approved hoses. Do not remove hose spring guards, which help protect the hose
from rupture caused by kinks or bends near the couplings.

Use fluids or solvents that are compatible with the equipment wetted parts. See the Technical
Data
 section of all the equipment manuals. Read the fluid and solvent manufacturer’s warnings.

Comply with all applicable local, state and national fire, electrical and other safety regulations.

MOVING PARTS HAZARD

Moving parts, such as the air motor piston, can pinch or amputate fingers.

Do not operate the equipment with the air motor plates removed.

Keep clear of any moving parts when starting or operating the equipment.

Содержание President 236-066













Отзывы: