manualshive.com logo in svg

Graco NAUTILUS, Руководство пользователя, Страница: 46 / 64

Поделиться
Скачать
Graco NAUTILUS Скачать руководство пользователя страница 46

46

14.0 Securing Child & Booster Seat in Vehicle

1. Place booster seat firmly against the back of a 
forward-facing vehicle seat. The vehicle seat must 
be equipped with a lap/shoulder belt.

2. Place child in car seat with child’s back flat 
against back of car seat.

3. Position lap/shoulder belt through shoulder belt 
guide 

 not underneath shoulder belt guide 

. 

Belt should pass over vehicle belt guide 

. Fasten 

buckle and pull up on the shoulder belt to tighten.

4. If belt lays across child’s neck, head or face,  
redirect belt over shoulder by adjusting the  
head support setting, 

See page 47,  

Adjusting Head Support. 

5. Check that shoulder belt is properly positioned  
over shoulder and snug against child. A snug strap 
should not allow any slack. It lies in a relatively  
straight line without sagging. It does not press 
on the child’s flesh or push the child’s body into  
an unnatural position.

Содержание NAUTILUS

































































Отзывы:

Нет отзывов