background image

For non-corrosive and non-abrasive oils and lubricants only. For professional use only. 

Not for use in explosive atmospheres.

.

Model No. 246775, Series B, Universal
Model No. 248097, Series B, Variable Length

540 psi (3.7 MPa, 37 bar) Maximum Working Pressure

180 psi (1.24 MPa, 12.4 bar) Maximum Air Input Pressure

Contents

Warnings   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2

Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4

Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6

Troubleshooting   . . . . . . . . . . . . . . . . . . . . . . . . . . .  7

Air Motor and Throat Service  . . . . . . . . . . . . . . . . .  8

Displacement Pump Service   . . . . . . . . . . . . . . . .  12

Parts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14

Technical Data  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16

Performance Chart   . . . . . . . . . . . . . . . . . . . . . . . .  16

Dimensional Drawings  . . . . . . . . . . . . . . . . . . . . .  17

Mounting Hole Layout . . . . . . . . . . . . . . . . . . . . . .  17

Graco Standard Warranty  . . . . . . . . . . . . . . . . . . .  18

Graco Information  . . . . . . . . . . . . . . . . . . . . . . . . .  18

Important Safety Instructions

Read all warnings and instructions in this 
manual. Save these instructions.

Instructions-Parts

3:1 Mini Fire-Ball

®

225 Oil Pump

ti4062b

309868E

EN

Содержание Mini Fire-Ball 248097



















Отзывы: