manualshive.com logo in svg

Graco Merkur W10CAS, Сборка, Страница: 31 / 32

Поделиться
Скачать
Graco Merkur W10CAS Скачать руководство пользователя страница 31

Technical Data

312794F

31

Technical Data

Maximum fluid working pressure  . . . . . . . . . . . . . . . . . . . See Models, page 4
Maximum air inlet pressure  . . . . . . . . . . . . . . . . . . . . . . . See Models, page 4
Minimum air inlet pressure . . . . . . . . . . . . . . . . . . . . . . . . 10 psi (0.07 MPa, 0.7 bar)
Air consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Performance Charts
Fluid flow at 60 cycles per minute  . . . . . . . . . . . . . . . . . . See Models, page 4
Maximum ambient air temperature. . . . . . . . . . . . . . . . . . 120°F (49°C)
Maximum fluid temperature  . . . . . . . . . . . . . . . . . . . . . . . 160°F (71°C)
Stroke length  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 in. (63.5 mm)
Sound data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Technical Data in air motor manual 312796.
Wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stainless steel, tungsten carbide with 6% nickel,

UHMWPE, PTFE

Содержание Merkur W10CAS

































Отзывы:

Нет отзывов