Graco magnum pro plus a20 Скачать руководство пользователя

Страница: 29 / 60

Control Board Diagnostics

332697C

Control Board Diagnostics

A60

NOTE:

Check for motor problems before replacing con-

trol board. A damaged motor may burn out a good con-
trol board.

Check for a damaged control board or pressure control
switch as follows:

Relieve Pressure

(see

Pressure Relief Proce-

dure

, page 13).

2. Unplug electrical cord.

3. Remove four cover screws and front cover.

Remove motor enclosure.

4. Remove yoke and guide rods.

5. Remove gear.

6. Remove pressure control harness from control

board. Using tip of small, flat blade screwdriver,
press tab on right side connector to release.

7. Attach harness from a pressure control switch you

know is functioning correctly to control board.

NOTE:

Pressure control switch does not have to be

installed in pump.

8. Turn pressure control adjustment knob (C) +to max-

imum pressure setting.

9. Plug electrical cord into 240 VAC receptacle.

10. Turn power switch (B) ON.

•

If motor runs, replace failed pressure switch.

Pressure Control Switch Kit

. See

List of Kits

page 30.

•

If motor does not run, replace control board
repeat test.

Control Board Kit

. See

List of

Kits

, page 30.

A20, A30, and A45

NOTE:

Check for motor problems before replacing con-

trol board. A damaged motor may burn out a good con-
trol board.

1. Unplug electrical cord and

relieve pressure

(see

Pressure Relief Procedure

, page 13).

2. Remove enclosure and check all control board

connectors for proper installation (see

Wiring

Diagram

, page 53).

3. Check fuse on control board. If fuse is blown,

determine the cause before replacing control board
(see

Advanced Troubleshooting

, page 20).

Содержание magnum pro plus a20





























































Результаты поиска

Содержание magnum pro plus a20

Отзывы:

Похожие инструкции для magnum pro plus a20

Бренды по названию

Популярные бренды

Graco magnum pro plus a20, Руководство по ремонту

Результаты поиска

Содержание magnum pro plus a20

Отзывы:

Похожие инструкции для magnum pro plus a20

Бренды по названию

Популярные бренды