Graco magnum pro plus a20 Скачать руководство пользователя | Manualshive

Страница: 13 / 60

background image

Operation

332697C

13

Operation

See

Operation

manual for basic information on sprayer

setup, flushing, and storage.

Trigger Lock

Always engage the trigger lock when you stop spraying
to prevent the gun from being triggered accidentally by
hand or if dropped or bumped.

Pressure Relief Procedure

Follow this

Pressure Relief Procedure

whenever you

stop spraying and before cleaning, checking, servicing,
or transporting equipment.

1. Turn power switch OFF and unplug power cord.

2. Move Prime/Spray valve to PRIME to relieve pres-

sure.

3. Hold gun firmly to side of pail. Trigger the gun to

relieve pressure.

4. Engage trigger lock.

NOTE:

Leave Prime/Spray valve in the PRIME position

until you are ready to spray again.

If you suspect the spray tip or hose is clogged or that
pressure has not been fully relieved after following the
steps above, VERY SLOWLY loosen tip guard retaining
nut or hose end coupling to relieve pressure gradually,
then loosen completely. Clear hose or tip obstruction.
See Unclogging Spray Tip in the

Operation

manual.

Pressure Control Knob Settings

NOTE:

To select function, align symbol on pressure control knob with setting indicator on sprayer.

ti8908a

Trigger Locked

Trigger Unlocked

ti8909a

ti2810a

ti9346a

ti13961a

A20 Only

ti9207a

ti8908a

High Pressure

Spray

Low Pressure

Spray

Prime/

Clean

Rolling

ti5597a

«
...
11
12
13
14
15
...
»

Содержание magnum pro plus a20





























































Отзывы:

Нет отзывов

Похожие инструкции для magnum pro plus a20

SPRAY SYSTEM HV 1900

Бренд: Earlex Страницы: 22

SPRAY STATION HV3500

Бренд: Earlex Страницы: 2

Бренд: WAGNER Страницы: 36

Бренд: Hozelock Страницы: 6

Бренд: Ryobi Страницы: 48

Бренд: Hozelock Страницы: 24

TS1500 B Series

Бренд: Graco Страницы: 34

Бренд: Tekmar Страницы: 12

Бренд: Rutland Страницы: 2

Бренд: HSS Hire Страницы: 2

Бренд: Rapid Spray Страницы: 32

Бренд: DeVilbiss Страницы: 6

Бренд: Graco Страницы: 46

Бренд: DeVilbiss Страницы: 9

Бренд: Orion Страницы: 4

Бренд: Graco Страницы: 52

Бренд: Gema Страницы: 45

Бренд: ASM Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды