Graco LubePro A4000 Скачать руководство пользователя страница 26

Страница: 26 / 38

Parts: Oil Models

3A5266G

Reassemble the Air Motor (F

. 30 and F

31)

NOTE:

For easier reassembly, start with the top cover

(210) turned over on the workbench and assemble the

air motor upside-down.
1. Lubricate and install the o-ring (202*) on the top

cover (210).

2. Lubricate the inside of the cylinder (205). Lower the

cylinder onto the top cover (210).

3. Install the shield (206) around the cylinder (205) and

in the groove on the top cover (210).

4. Lubricate and install a new u-cup seal (207*) in the

bottom of the bearing in the bottom cover (201).

The lips must face down. Lubricate and install a

new u-cup seal (207*) in the top of the bearing. Lips

must face up to install the retaining ring (217).

5. Lubricate and install the o-ring (202*) on the bottom

cover (201).

6. Carefully push the threaded end of the rod (218) up

through the bottom cover (201).

7. Apply 16G561 adhesive to the threads of the rod

(218). Screw the piston (219) onto the rod. Place

the piston in a vise with soft jaws and torque to

35-40 ft-lb (47-54 N•m).

8. Lubricate and install the o-ring (204*) on the piston

(219).

9. Carefully place the bottom cover/piston assembly

on the cylinder (205), sliding the piston (219) into

the cylinder. The manifold surfaces of the top and

bottom covers must align. Be sure the shield (206)

is in the groove on both the top and bottom covers.

10. Install the tie bolts (212) hand tight.

11. Install two gaskets (208*) on the manifold (220).

Install the manifold (220). Torque screws (211) to

95-105 in-lb (10.7-11.9 N•m).

NOTE:

The manifold is reversible for ease of placement

of muffler or remote exhaust.

12. Align the air valve gasket (209*

◆

†) on the manifold,

then attach the air valve (214). Torque screws (211)

to 95-105 in-lb (11-12 N•m).

13. Tighten the tie bolts (212) halfway. Work in a criss

cross pattern. Check that the shield (206) remains

in the grooves on both covers. Continue tightening

the bolts in pattern to 11-13 ft-lb (15-18 N•m).

14. Lubricate and install pilot valves (213) in top and

bottom cover. Torque to 95-105 in-lb (11-12 N•m).

15. See

Air Motor

nstallation

on page 27.

. 30

*207

Lips face up

Lips face down.

. 31

groove

201

206

210

Содержание LubePro A4000







































Результаты поиска

Содержание LubePro A4000

Отзывы:

Похожие инструкции для LubePro A4000

Бренды по названию

Популярные бренды

Graco LubePro A4000, Инструкция по эксплуатации

Результаты поиска

Содержание LubePro A4000

Отзывы:

Похожие инструкции для LubePro A4000

Бренды по названию

Популярные бренды