manualshive.com logo in svg

Graco LineLazer IV 3900, Список запасных частей и инструкция по ремонту

Поделиться
Скачать
Graco LineLazer IV 3900 Скачать руководство пользователя страница 11

Bearing Housing and Connecting Rod

312195B

11

Bearing Housing and Connecting Rod

Removal

1.

Relieve pressure, page 6.

2.

F

IG

. 2. Remove screws (187) and front cover (83). 

3.

Unscrew suction tube (34) from pump, hold wrench on 
pump intake valve (A) to keep pump from loosening.

4.

Disconnect pump outlet hose (100) from displace-
ment pump outlet nipple (60).

5.

F

IG

. 1. Use screwdriver to push up retaining spring 

(236) at top of pump. Push out pin (235).

6.

F

IG

. 2. Loosen retaining nut (84). Unscrew and 

remove displacement pump (21).

7.

Remove four screws (183) and lockwashers (188) 
from bearing housing (22).

8.

Pull connecting rod (26) and lightly tap lower rear of 
bearing housing (22) with plastic mallet to loosen 
from drive housing (24). Pull bearing housing and 
connecting rod assembly (26) off drive housing.

9.

Inspect crank (B) for excessive wear and replace 
parts as needed.

Installation

1.

Evenly lubricate inside of bronze bearing (C) in bear-
ing housing (22) with high-quality motor oil. Liberally 
pack top roller bearing (E), lower bearing (D) inside 
connecting rod assembly (26) with bearing grease.

2.

Assemble connecting rod (26) and bearing housing (22).

3.

Clean mating surfaces of bearing and drive housings.

4.

Align connecting rod with crank (B) and carefully 
align locating pins (F) in drive housing (24) with holes 
in bearing housing (22). Push bearing housing onto 
drive housing or tap into place with plastic mallet.

5.

Install screws (183) and lockwashers (188) on bear-
ing housing. Torque evenly to note 3 value in F

IG

. 2.

6.

Install pump. Refer to 

Displacement Pump

, 

Instal-

lation

, page 21.

F

IG

. 1

235

236

7675b

CAUTION

Do not use bearing housing screws (183) to align or seat 
bearing housing with drive housing. Align these parts 
with locating pins (F), to avoid premature bearing wear.

F

IG

. 2

1

2

3

B

E

D

236

83

187

183

235

21

A

60

100

34

84

34g

22

24

F

C

26

188

3

2

Oil.

Pack with bearing grease 114819.

LineLazer IV 3900: Torque to 200 in-lb (22.6 N•m).
LineLazer IV 5900: Torque to 25 ft-lb (34 N•m).

1

2

3

TI6395A

Model 253920

Содержание LineLazer IV 3900







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды