Graco HEH006 Скачать руководство пользователя страница 17

Страница: 17 / 26

Repair

3A8216B

Repair

Replace the Hose

(Kits listed on page 22)

Follow the

Pressure Relief Procedure

, page 8.

Fully extend the hose (B) and latch the reel (F

12).

Attach a C-clamp (A) to the reel flange to prevent
the reel from unintentionally becoming unlatched
and spinning freely (F

. 12).

Remove the hose stop from the hose end and put all
of the parts in a secure place for re-installation on
the new hose (F

. 13).

Loosen and remove screws and nuts (F

. 13).

Separate the two hose stop components to

remove from the end of the hose (F

. 13).

SPRING TENSION HAZARD

The hose reel spring is always under great tension,
which if released in an uncontrolled manner could
cause serious injury.

•

The hose reel spring is not a serviceable part. Do
not attempt to replace or service the hose reel
spring.

•

Never allow the reel to spin freely. Uncontrolled
spinning could cause serious injury if hit by the
hose.

•

Securely fasten the reel in place while making
adjustments.

•

Always wear heavy gloves while adjusting the
spring tension to protect your hands from being
cut on the hose reel.

. 12

. 13

Screws

Nuts

Hose Stop
Components

Содержание HEH006



























Результаты поиска

Содержание HEH006

Отзывы:

Graco HEH006, Установка, ремонт и запчасти, Страница: 17 / 26

Результаты поиска

Содержание HEH006

Отзывы: