manualshive.com logo in svg

Graco GM3500 SPRAYER 231-078, Инструкция-перечень запасных частей

Поделиться
Скачать
Graco GM3500 SPRAYER 231-078 Скачать руководство пользователя страница 19

19

308-709

Drive Housing

WARNING

To reduce the risk of serious bodily injury always
follow the Pressure Relief Procedure Warning on
page 12 before checking, adjusting, cleaning or
shutting down the sprayer.

NOTE: Refer to Fig. 12 for this procedure.

1.

Remove the front cover (23).

2.

Disconnect the hose (55) from the pump nipple
(83). For the upright carts only, detach the drain
hose (91) from the pump.

3.

Remove the four screws (69) and lockwashers
(70) from the bearing housing (21).

4.

Lightly tap the back of the bearing housing with a
plastic mallet. Pull the pump, bearing housing and
connecting rod away from the drive housing as
one assembly.

5.

Remove the two screws (24) and lockwashers
(11). Remove the four screws (10) and 
lockwashers (11).

6.

Lightly tap around the drive housing (20) with a
plastic mallet to loosen it from the pinion housing
(19n).

CAUTION

DO NOT drop the gear cluster (18) when removing
the drive housing (20). The gear cluster is easily
damaged. The gear may stay engaged in either the
drive housing or the pinion housing.

DO NOT lose the thrust balls (20c and 19j) located at
each end of the gear cluster. The balls, which are
heavily covered with grease, usually stay in the shaft
recesses, but they could be dislodged. If they are
caught between the gears and not removed, the balls
will seriously damage the drive housing. If the balls
are not in place, the bearings will wear prematurely.

7.

Liberally apply bearing grease (20d, supplied) to
the gear cluster (18). Be sure the thrust balls (20c
and 19j) are in place.

8.

Place the bronze colored washer (20a) and then
the silver-colored washer (20b) on the shaft pro-
truding from the big bearing of the drive housing
(20). Align the gears and push the new drive
housing straight onto the pinion housing and
locating pins (B).

9.

Starting at Step 5, work backwards to reassemble
the sprayer. Or, move ahead to the next section in
this manual if further service is needed.

Fig. 12

10

11

19j

18

20c

11

24

64

23

22

20

20a

20b

19n

11

10

B

70

69

83

21

91

55

0170A

1

1

Torque to 300 

"

20 in-lb

(34 

"

2.3 N

m)

Содержание GM3500 SPRAYER 231-078





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды