Graco GLASCRAFT Indy Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 30

background image

20

GC-1306S

Trigger & Needle Guard Readjustment Procedure

If you trigger the gun and notice that one needle is activating before

the other and not parallel, fine adjustment is needed.

1.

Using a 5/64in. hex key adjust the Set Screw which is NOT making

gun pin contact when the gun is triggered. Turn the set screw until
both needles activate at the same time.

Making the needle guard

parallel is very important, to prevent LAG-LEAD in the catalyst
& resin mix.

NOT OK

Set Screws 5/64in. hex key

Maintenance

«
...
18
19
20
21
22
...
»

Содержание GLASCRAFT Indy































Отзывы:

Нет отзывов

Похожие инструкции для GLASCRAFT Indy

Бренд: ABB Страницы: 14

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

Бренд: JB-Lighting Страницы: 60

Бренд: made for movement Страницы: 51

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: Radial Engineering Страницы: 2

Бренд: Radial Engineering Страницы: 2

Бренд: Vapotherm Страницы: 32

Бренд: Vanguard Instruments Страницы: 47

Бренд: M-Audio Страницы: 3

Бренд: Xtralis Страницы: 26

Бренд: Yamaha Страницы: 4

Бренд: Wacker Neuson Страницы: 120

Бренд: Igema Страницы: 22

Бренд: MAGSTIM Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды