background image

Warnings

335023J

3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The 
exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. 
When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. 
Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this 
manual where applicable.

+

SKIN INJECTION HAZARD

 

High-pressure fluid from injector, hose leaks, or ruptured components will pierce skin. This may look like 
just a cut, but it is a serious injury that can result in amputation. 

Get immediate surgical treatment.

Do not put your hand over the fluid outlet.

Do not stop or deflect leaks with your hand, body, glove, or rag.

Relieve pressure

 before cleaning, checking, or servicing equipment. 

Tighten all fluid connections before operating the equipment.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including 
eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is 
not limited to:

Protective eyewear, and hearing protection. 

Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

CALIFORNIA PROPOSITION 65

This product contains a chemical known to the State of California to cause cancer, birth defects or other 
reproductive harm. Wash hands after handling.

WARNING

Содержание GL-1 X













Отзывы: