manualshive.com logo in svg

Graco G3-G-12MX-2L0L00-10C00000, Инструкция по эксплуатации

Поделиться
Скачать
Graco G3-G-12MX-2L0L00-10C00000 Скачать руководство пользователя страница 35

Max Model Setup

332305G

35

•

In SETUP MODE, the number displayed in the first 
field, on the left side of display blinks, indicating the 
device is ready to program the ON Time minutes. 

•

The total amount of ON Time cannot 
exceed 30 minutes. If a value greater 
than 30 minutes is entered, the RED 
alarm LED lights and the value must 
be updated.

If this time does not meet the application needs, 
contact Graco Customer Support.

Programming ON Time

NOTE: 

When programming a time of less than 10 min-

utes

 

you 

must

 program a leading zero in the first num-

ber field and press the ENTER button to save the zero 
selection.

1.

To set the ON Time use the 
UP or DOWN ARROW button 
to scroll through numerals 0 
to 5 until the desired number 
appears in the first MM (min-
utes) field.

2.

Press the ENTER button to lock in the 
selection. The next MM number field to 
the right flashes indicating it is ready for 
programming. 

3.

Use the UP or DOWN 
ARROW button to scroll 
through numerals 0 to 9 until 
the desired number appears 
in the second MM number 
field.

4.

Press the ENTER button to lock in the 
selection.

The next number field to the right 
flashes and the LED lights under SS; indicating it is 
ready to program the seconds fields. 

5.

Repeat steps 1 - 4 to set the SS (seconds) fields.

6.

After pressing the ENTER button to set 
the last SS field, all the programmed ON 
Time information is saved. 

The G3 automatically switches to the OFF Time 
SETUP MODE. 

PUMP OFF / REST Setup

After setting the parameters for either Cycle (C1, C2 or 
C3) or Pressure (P1, P2, or P3) ON modes, the OFF or 
pump rest cycle must be set up. There are 3 ways to 
control this function:

•

Machine Count switch activation, or 

•

Machine Count activations limited by a maxi-
mum Time, or 

•

A specific set amount of Time (similar to Time 
Mode).

•

If the machine count sensor input is available 
and not used in the OFF Mode, the definition of 
the entered time is OFF TIME.

Machine Count

1.

After you set the last ON Time field 
and press the ENTER button, the G3 
automatically switches to the 
Machine Count setup. 

Notice the LED next to 123 on the G3 display lights 
indicating you are now in the Machine Count setup 
mode.

2.

Press the UP or DOWN 
ARROW button to move up or 
down through number 0-9.

3.

When the correct number displays, 
press the ENTER button to set the num-
ber. 

NOTE:

 If the machine count input is available on the unit 

and not used, the value MUST be set to zero (0).

4.

Repeat 2 - 3 to set the remaining fields.

NOTE:

 After the Machine Count value is entered, the G3 

can be programmed to backup the machine count input 
with time. 

Backup Time Setup

1.

The OFF Time LED lights.

Содержание G3-G-12MX-2L0L00-10C00000









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды