Graco EFR Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 70

Graco EFR Скачать руководство пользователя страница 58

Software Update

58

3A6165J

Software Update

NOTE:

If burning your own software token, see the ADM

Token Programming manual. See

Related Manuals

on

page 2. Otherwise, proceed to

17Y711 Software

Update Procedure

.

17Y711 Software Update
Procedure

NOTE:

A token can be found in the ADM token compart

-

ment.

When software is updated on the ADM the software is
then automatically updated on all connected modules. A
status screen is shown while software is updating to
indicate progress.

1. Turn power disconnect switch (C) to the OFF

position.

2. Remove ADM from bracket.

3. Remove token access panel (BK).

4. Insert and press EFR software upgrade token (TK,

part no. 17Y711) firmly into slot.

NOTE:

There is no preferred orientation of token.

5. Turn the power disconnect switch (C) to the ON

position.

NOTE:

When the ADM display turns on, you may see

the following screens:

6. Remove token (TK).

7. Replace token access panel (BK).

8. Install ADM into bracket.

9. Press

to continue to EFR operation screens.

BK

ADM

TK

NOTICE

A status is shown while software is updating to
indicate progress. To prevent corrupting the software
load, do not remove token until the status screen
disappears.

First:

Software is checking
which modules will take
the available updates.

Second:

Status of the update with
approximate time until
completion.

Third:

Updates are complete.
Icon indicates update
success/failure. See the
following Icon table.

Icon

Description

Update successful.

Update unsuccessful.

Update complete, no changes necessary.

Modules were updated or didn’t require an
update; however, one or more modules need to
be updated manually with a token.

«
...
56
57
58
59
60
...
»

Содержание EFR







































































Отзывы:

Нет отзывов