background image

Maintenance

Maintenance

Flushing Procedure

Note:
• Flush before fluid can dry in the equipment, at the

end of the day, before storing, and before repairing

equipment.

• Flush at the lowest pressure possible. Check

connectors for leaks and tighten as necessary.

• Flush with an appropriate cleaning solution.
1. Follow

Pressure Relief Procedure, page 8

.

2. Remove the pump from the fluid container. Place

it in an empty drum. Operate it to pump out as

much fluid as possible.

3. Place siphon tube in grounded metal pail

containing an appropriate cleaning solution.

4. Set pump air regulator to lowest possible fluid

pressure, and start pump.

5. Run the pump long enough to thoroughly clean

the pump and hoses.

6. Follow

Pressure Relief Procedure, page 8

.

Cleaning

• Be sure to follow your national and state sanitary

standard codes and local regulations.

• Use appropriate cleaning and disinfecting agents,

at intervals appropriate for product processed.

• Follow cleaning product manufacturer’s

instructions.

Note: The pump lower must be disassembled to

thoroughly clean it.
1. Follow the

Pressure Relief Procedure, page 8

.

2. Remove the pump from the fluid container. Place

it in an empty drum Operate it to pump out as

much fluid as possible.

3. Flush the system thoroughly with an

appropriate cleaning solution. See

Flushing Procedure, page 9

.

4. Follow the

Pressure Relief Procedure, page 8

.

5. Remove the air and fluid hoses and fittings from

the pump.

6. Disassemble the fluid pump and accessories.

See

Disassemble the Pump, page 15

.

7. Wash all pump parts with an appropriate cleaning

solution at the cleaning product manufacturer’s

recommended temperature and concentration.

8. Rinse all pump parts again with water and allow

them to dry.

9. Inspect all pump parts and reclean if needed.

Note

Any damaged rubber parts must

be replaced as they could harbor

microorganisms that can contaminate

the fluid.

10. Immerse all pump parts in an appropriate

sanitizer before assembly. Take the pump parts

out of the sanitizer one-by-one as needed.

11. Lubricate the moving pump parts and o-rings,

packings, and seals with appropriate waterproof

sanitary lubricant.

12. Circulate the sanitizing solution through the pump

and the system prior to use.

Tighten Threaded Connections

Before each use, check all hoses for wear or damage.

Replace as necessary. Check that all connections

are tight and leak-free.

3A2977K

9

Содержание 3A2977K





























Отзывы: