manualshive.com logo in svg

Graco 26C265, Инструкция по эксплуатации, Страница: 1 / 40

Поделиться
Скачать
Graco 26C265 Скачать руководство пользователя страница 1

Instructions

Automatic Airless 
Spray Guns

311053L

EN

Part 26C624

For use with spraying high-pressure protective coating materials.

5000 psi (35 MPa, 345 bar) Maximum Working Fluid Pressure

Part 288048

For airless spraying of paints and coatings.

5000 psi (35 MPa, 345 bar) Maximum Working Fluid Pressure

Part 288554

For sealant streaming applications.

5000 psi (35 MPa, 345 bar) Maximum Working Fluid Pressure

Part 26C625

For use with spraying high-pressure protective coating materials.

7250 psi (50 MPa, 499 bar) Maximum working Pressure

Mounting manifolds must be ordered separately. Refer to Parts section.

Important Safety Instructions

Read all warnings and instructions in this 
manual before using the equipment. 
Save these instructions. 

Important Medical Information

Read the medical alert card provided with 
the gun. It contains injection injury 
treatment information for a doctor. Keep it 
with you when operating the equipment.

Models 288048 and 288554

Model 26C624

Model 26C265

II 2 G Ex h IIB T6 Gb

Содержание 26C265









































Отзывы:

Нет отзывов