Graco 262893 Скачать руководство пользователя страница 21

Страница: 21 / 22

Technical Data

3A2988C

Technical Data

Maximum working pressure . . . 6000 psi (41 MPa, 414 bar) for A and B materials

4500 psi (31 MPa, 310 bar) for flushing fluid
100 psi (0.7 MPa, 7 bar) for heating fluid

Maximum fluid temperature . . . 180°F (82°C)

Fluid inlet . . . . . . . . . . . . . . . . . 3/4 in. npt and 3/4 in. x 1/2 in. nipple fittings for 3/4 in. x 1/2 in. hoses

Fluid outlet size . . . . . . . . . . . . . 1/2 in. npt(m) nipple

Solvent inlet valves . . . . . . . . . . 1/4 in. npt(m)

Heated fluid ports . . . . . . . . . . . 1/4 in. npt(f)

Wetted parts . . . . . . . . . . . . . . .

Manifold block and internal parts:

PTFE, electroless nickel plated steel, zinc plated

steel

Flush valves and fittings:

stainless steel, plated carbon steel, hardened alloy steel,

acetal, PTFE

Fluid ball valves:

plated carbon steel, acetal, PTFE, FKM

Fluid check valves:

plated carbon steel, carbide seat, PTFE, alloy steel ball

Содержание 262893























Результаты поиска

Содержание 262893

Отзывы:

Похожие инструкции для 262893

Бренды по названию

Популярные бренды

Graco 262893, Инструкция - Каталог запасных частей

Результаты поиска

Содержание 262893

Отзывы:

Похожие инструкции для 262893

Бренды по названию

Популярные бренды