Graco 25U546 Скачать руководство пользователя страница 31

Страница: 31 / 48

Troubleshooting

3A9031A

Pump output is low

Pump rod damage.

Repair pump. See pump

manual.

Low stall pressure (pressure

setting too low).

Turn pressure knob fully

clockwise. Make sure pressure

control knob is properly

installed to allow full clockwise

position. If problem persists,

replace pressure control.

Piston packings are worn or

damaged.

Replace packings. See pump

manual.

O-ring in pump is worn or

damaged.

Replace o-ring. See pump

manual.

Intake valve ball is packed with

material.

Clean intake valve. See pump

manual.

Large pressure drop in hose

with heavy materials.

Reduce overall length of hose.

Motor runs but pump does not

stroke

Connecting rod assembly

damaged. See pump manual.

Replace connecting rod

assembly. See pump manual.

Gears or drive housing

damaged.

Inspect drive housing

assembly and gears for

damage and replace if

necessary.

Excessive paint leakage into

throat packing nut

Throat packing nut is loose.

Remove throat packing nut

spacer. Tighten throat packing

nut just enough to stop

leakage.

Throat packings are worn or

damaged.

Replace packings. See pump

manual.

Displacement rod is worn or

damaged.

Replace rod. See pump

manual.

Fluid is spitting from gun

Air in pump or hose.

Check and tighten all fluid

connections. Cycle pump as

slowly as possible during

priming.

Spray tip is partially clogged.

Clear tip. See

Clear Tip Clog

page 23.

Fluid supply is low or empty.

Refill fluid supply. Prime

pump. See pump manual.

Check fluid supply often to

prevent running pump dry.

Problem

What to Check

If check is OK, go to next

check

What to Do

When check is not OK,

refer to this column

Содержание 25U546

















































Результаты поиска

Содержание 25U546

Отзывы:

Похожие инструкции для 25U546

Бренды по названию

Популярные бренды

Graco 25U546, Руководство пользователя

Результаты поиска

Содержание 25U546

Отзывы:

Похожие инструкции для 25U546

Бренды по названию

Популярные бренды