background image

Operation 

14

3A5202G

Changing Material and Storing 
Equipment

1. Follow 

Shutdown

, page 12, steps 1-11. Do not 

reconnect fittings or reinstall mixing tube.

2. Vacuum and/or hose down the hopper and dosing 

shaft. Make sure all the dosing/breaker elements 
are clean.

3.

For storage and use in freezing temperatures:

 

Drain the water. Remove twist-claw irrigation fitting 
(DG) and open water accessory ball-valve (DB). 
Carefully tilt the unit to allow water to drain from 
both ends of the water control assembly (D), which 
is separated by the closed water control solenoid 
(DE). Ensure water has also been drained from the 
water output hose and water dosing port (FCC) in 
the throat insert (FC).

4. Reconnect all fittings and reinstall the mixing tube 

assembly onto the throat insert. Ensure the pins 
(FBB) on the mixing shaft (FB) line up with the slots 
in the material dosing shaft (FD).

Avoid contact with the discharge nozzle (FF), mix 
shaft (FB), and material dosing auger shaft (FD) 
during preparation for changing material or storing 
equipment. These parts can pull in, crush, cut, or 
amputate fingers and other body parts.

Do not use pressurized water jets to clean electrical 
box, motor, capacitors, or wires. Use of pressurized 
water jets can cause water to enter the electrical 
controls and increase potential for electric shock.

NOTICE

If water is used to clean hopper (A) or material dosing 
auger shaft (FD), allow equipment to fully dry before 
placing more dry material in the hopper. A wet hopper 
or auger shaft can cause dry material to cure onto 
mixer parts.

NOTICE

If working in a cold environment, failure to drain water 
from the water control assembly (D) could cause 
damage to the system due to freezing water.

WLD

)'

)%

)%%

Содержание 25M081

































Отзывы: