Graco 25C536 Скачать руководство пользователя страница 27

Страница: 27 / 28

Technical Specifications

Technical

Technical Specifications

Specifications

Actual tank capacities

5-gallon

8.8 gallons (33 liters)

10-gallon

12.6 gallons (48 liters)

15-gallon

19.3 gallons (72 liters)

Tank inlet/outlet sizes

Air inlet size

1/4–18 npt (m)

Fluid outlet size

3/8–18 npsm (m)

Bottom outlet size

3/4–14 npt (f)

Wetted parts

304 and 316 stainless steel, PTFE, nylon, and bronze.
Splashed materials: LDPE, Chloroprene, Santoprene

Weight

25C536

66 lbs (30 kg)

25C537

77 lbs (35 kg)

25C538

93 lbs (42 kg)

25C539

13 lbs (5.9 kg)

25C540

14 lbs (6.4 kg)

25C541

15 lbs (6.8 kg)

Maximum working pressure, high
pressure regulated tank

100 psig (0.7 MPa, 7 bar)

Maximum recommended operating
pressure, agitator

70 psig (0.5 MPa, 5 bar)

Tank relief valve setting

100 psi (0.7 MPa, 7 bar)

Maximum allowable process fluid
temperature

158° F (70° C)

Recommended agitator speed
range for adequate agitation

40–60 rpm

Recommended maximum agitator
speed (higher speeds may
over-agitate the material and
decrease shaft seal life)

60 rpm

Recommended maximum material
viscosity

1000 cP

Sound pressure level at 70 psig,
maximum recommended speed

Less than 75 dBA

Note:

Santoprene

is a registered trademark of the Monsanto Co.

California

California Proposition

Proposition

Proposition 65

WARNING:

WARNING: This product can expose you to chemicals known to the State of California

to cause cancer and birth defects or other reproductive harm. For more information, go to

www.P65warnings.ca.gov.

3A4797F

Содержание 25C536





























Результаты поиска

Содержание 25C536

Отзывы:

Похожие инструкции для 25C536

Бренды по названию

Популярные бренды

Graco 25C536, Инструкция - Каталог запасных частей

Результаты поиска

Содержание 25C536

Отзывы:

Похожие инструкции для 25C536

Бренды по названию

Популярные бренды