background image

Operation

3A5414A

5

Operation

Once the Pulse HUB is installed, verify that 
the power light (D) (F

IG

. 5) is ON and the HUB 

is functioning correctly. 

When the green power light (D) is illuminated 
it indicates the unit is receiving AC power.

The status of the Pulse Fluid Management 
Software is indicated by the HUB Status Light 
(G) (F

IG

. 5). See HUB Status Lights table 

below for diagnostic definitions.

HUB Diagnostics (D)

HUB Status Light (G)

NOTE:

 On system boot the SBC will cycle through the LED status lights to confirm they are 

functional.

F

IG

. 5

D

G

Indicator

Diagnostic Definition

No green power 
light

Indicates that AC power is not connected. Verify that the power adapter is 
securely plugged into the component and the AC power outlet

Verify that the AC power outlet is “live”.

Indicator

Diagnostic Definition

Solid Green with Blinking 
Orange

HUB is running normally using Ethernet.

Solid Green with Blinking 
Red

HUB is running normally using WiFi.

Blinking Green with 
Blinking Orange

HUB is launching or updating using Ethernet.

Blinking Green with 
Blinking Red

HUB is launching or updating using WiFi.

Solid Red

HUB has a critical systems failure.

Solid Red with Blinking 
Orange

HUB has a critical systems failure with the device network.

Solid Red with Blinking 
Green

HUB has a critical systems failure with the Pulse application.

Содержание 24Z978













Отзывы: