background image

Setup 

8

334198K

Setup

Refer to the Therm-O-Flow 200 and Therm-O-Flow 20, 
Instructions-Parts manuals for additional setup proce-
dures such as unpacking, location requirements, and 
component installations.

Grounding

Refer to the Therm-O-Flow 200 and Therm-O-Flow 20, 
Instructions-Parts manuals for the grounding of the unit.

Grounding the Hydraulic Power 
Supply

To ground the hydraulic power supply unit pump, con-
nect the ground wire and clamp to a true earth ground 
as shown.

1. Loosen the grounding screw and washer.

2. Insert one end of the 1.5 mm (12 gauge) minimum 

ground wire into the slot in the lug and tighten the 
locknut securely.

3. Connect the other end of the wire to a true earth 

ground. See F

IG

. 4. 

You must also provide an earth ground to the supply 
unit electrical control box. Make sure the ram is installed 
correctly to ensure that the ram is properly grounded.

For information about grounding other components in 
your system, see the system or supply unit documenta-
tion, as well as the documentation for individual compo-
nents.

The equipment must be grounded to reduce the risk of 
static sparking.  Static sparking can cause fumes to 
ignite or explode.  Grounding provides an escape wire 
for the electric current.

F

IG

. 4

WLD

Содержание 24W181































Отзывы: