background image

Installation 

10

3A1318B

Grounding

1.

Pump: 

See F

IG

. 3. Use the ground wire and clamp 

(41, supplied). Loosen the grounding screw (GS). 
Insert one end of the ground wire behind the 
grounding screw and tighten the screw securely. 
Connect the clamp end of the ground wire to a true 
earth ground. 

2.

Air and fluid hoses:

 Use only grounded hoses

 

with 

a maximum of 500 ft (150 m) combined hose length 
to ensure grounding continuity. 

3.

Air compressor: 

Follow manufacturer’s

recommendations.

4.

Spray gun: 

ground through connection to a prop-

erly grounded fluid hose and pump.

5.

Agitator: 

use the ground wire and clamp (108, sup-

plied). Loosen the grounding lug locknut (W) and 
washer (X). Insert one end of the ground wire (108) 
into the slot in lug (Z) and tighten the locknut 
securely. Connect the ground clamp to a true earth 
ground.

6.

Suction hose: 

Attach the hose (8) ground wire to 

the ground lug on the agitator. If you are not using 
an agitator, attach the wire to the fluid supply con-
tainer.

7.

Fluid supply container:

 Follow local code.

8.

Object being sprayed: 

Follow local code.

9.

Solvent pails used when flushing:

 Follow local 

code. Use only conductive metal pails, placed on a 
grounded surface. Do not place the pail on a non-
conductive surface, such as paper or cardboard, 
which interrupts grounding continuity.

10.

To maintain grounding continuity when flushing or 
relieving pressure

, hold a metal part of the spray 

gun firmly to the side of a grounded 

metal

 pail, then 

trigger the gun.

The equipment must be grounded. Grounding 
reduces the risk of static and electric shock by 
providing an escape wire for the electrical current 
due to static build up or in the event of a short circuit.

F

IG

. 3. Ground the Pump.

ti12214a

41

GS

F

IG

. 4. Ground Agitator and Suction Hose

ti0720a

8

108

W

X

Z

Содержание 24H313





























Отзывы: