Graco 248862 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

background image

311020

15

Clutch Housing

Removal

1. Fig. 10. Remove four cap screws (186) and lock

washers (188) which hold clutch housing (85) to

engine.

2. Remove screw (177) from under mounting

plate (96).

3. Pull off clutch housing (85).

Installation

1. Fig. 10. Push on clutch housing (5).

2. Install four cap screws (186) and lock washers

(188) and secure clutch housing (85) to engine.

Torque to 200 in-lb (22.6 N

S

m).

3. Install cap screw (177) from beneath mounting

plate (96). Torque to 26 ft-lb (35.2 N

S

m).

ti6643a

Fig. 10

186

188

85

88

177

96

«
...
13
14
15
16
17
...
»

Содержание 248862





































Отзывы:

Нет отзывов

Похожие инструкции для 248862

Бренд: NAD Страницы: 10

Бренд: tayco Страницы: 111

Бренд: Maeda Страницы: 276

Бренд: Milestone Страницы: 40

Firefly 808 Universal

Бренд: Phonic Страницы: 27

Бренд: Jäger Страницы: 36

Бренд: IMG STAGE LINE Страницы: 12

Бренд: Moog Страницы: 15

Бренд: Nexersys Страницы: 26

Бренд: ultraMEDIC Страницы: 28

Бренд: Evermed Страницы: 16

Бренд: Enerpac Страницы: 36

NOVACAT X8 COLL

Бренд: Pottinger Страницы: 91

HydraMaster driMaster HiFlo Upholstery Tool

Бренд: U.S. Products Страницы: 28

Бренд: Bowa Страницы: 44

Бренд: NeckXsystems Страницы: 12

Бренд: Foxfury Lighting Solutions Страницы: 17

Бренд: ZOLL Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды