background image

Manual Conventions 

2

309925B

Manual Conventions

Note

WARNING

WARNING

 indicates a potentially hazardous situation 

which, if not avoided, could result in death or serious 
injury.

CAUTION

CAUTION

 indicates a potentially hazardous situation 

which, if not avoided, may result in property damage or 
destruction of equipment.

A note indicates additional helpful information.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent 
fire and explosion:
  • Use equipment only in well ventilated area.
  • Eliminate all ignition sources, such as pilot lights, cigarettes, portable electric lamps, and plastic drop 

cloths (potential static arc).

  • Keep work area free of debris, including solvent, rags, and gasoline.
  • Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
  • Ground equipment and conductive objectives. See 

Grounding 

in your sprayer manual.

  • Use only grounded hoses.
  • Hold gun firmly to side of grounded pail when triggering into pail.
  • If there is static sparking or you feel a shock, 

stop operation immediately

. Do not use equipment 

until you identify and correct the problem.

PRESSURIZED ALUMINUM PARTS HAZARD

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids 
containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical 
reaction and equipment rupture, and result in death, serious injury, and property damage. 

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.
  • Do not exceed maximum working pressure or temperature rating of the lowest rated system compo-

nent. See 

Technical Data

 in all equipment manuals.

  • Use fluids and solvents that are compatible with equipment wetted parts. See 

Technical Data

 in all 

equipment manuals. Read fluid and solvent manufacturer’s warnings.

  • Check equipment daily. Repair or replace worn or damaged parts immediately.
  • Do not alter or modify equipment.
  • Use equipment only for its intended purpose. Call your Graco distributor for information.
  • For professional use only.
  • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
  • Comply with all applicable safety regulations.

Содержание 234413











Отзывы: