![background image](http://html1.mh-extra.com/html/graco/1k-ultra-lite-243482/1k-ultra-lite-243482_instructions-parts-list-manual_2251383020.webp)
20
308876
Service
(Models 243482 and 243666 only)
Reassembly
Air Cylinder Section
1.
Lubricate the shaft o-rings (4) and the bearings (5)
with grease supplied in the repair kit. Insert o-rings
into the air cylinder (1) and air cap (11) cavities.
See Fig. 5.
2.
Press the bearings (5) flush into the air cylinder
housing and air cap, trapping the o-rings (4).
3.
Lubricate and reassemble the piston assembly;
piston (10), o-ring (9), dowel pin (7), o-ring (6), and
shaft (3). Tighten the jam nut (45) to 15–20 in-lb
(1.7–2.2 N
S
m). The shaft (3) should hang with
some play to be self-aligning in the bearing.
4.
Lubricate the air cylinder (1) ID with the grease
supplied. Push the piston (10) assembly into the
air cylinder.
5.
Orient the air inlet manifold (2) (if used) as shown.
Match the gasket openings to the air ports.
Fluid Section
1.
Lubricate the bearing (21), o-ring (16) and cup seal
(20). Put the o-ring (16) on the bearing. Carefully
insert the seal (20) into the bearing recess, with
the lips of the o-ring facing into the bearing. Be
careful not to damage the seal lips.
2.
Push the bearing (21) seal end first into the
housing (19). Be sure that the grease hole in the
side of the bearing lines up with the grease ports in
the housing (19).
3.
Holding the bearing (21) in place, push the bearing
assembly over the shaft (3).
4.
Lubricate the main fluid seal (22) and its cavity in
the housing (26). Carefully press the seal, lip-first,
into the housing.
5.
Push the housing (26) and seal (22) over the shaft
(3) and up against the bearing housing.
6.
Apply Loctite Primer N7649 and Loctite TL242,
243, or equivalent (“blue” Loctite) to the fluid
housing screws (23) and loosely install the screws
to retain the housings. Do not tighten the screws
yet.
7.
Insert the gasket (38) and seat (25). These items
are reversible and can be installed in either
direction.
8.
Apply Loctite Primer N7649 and Loctite TL242,
243, or equivalent (“blue” Loctite) to needle (27)
and tighten to 15–20 in–lb (1.7–2.2 N
S
m).
9.
Apply air pressure to the CLOSE port, or to the
pneumatic trigger valve if installed. This will align
the shaft, seal, and bearing. Tighten the fluid
housing screws (23) oppositely and evenly to
40–45 in-lbs (4.5–5 N
S
m).
10. Install the nosepiece (40) with the PTFE o-ring
(39), screw (15), and snuff-back ring (41), if used.
The snuff-back ring has an internal bevel on one
end which faces into the nosepiece. Tighten the
nosepiece screws to 15–20 in-lbs (1.7–2.2 N
S
m).
Содержание 1K Ultra-Lite 243482
Страница 15: ...15 308876 Notes...
Страница 18: ...18 308876 Parts 8372A 8370A 63 46 48 49 51 52 58 59 57 50 965768 only 965767 only 47 8375B 61 60 53 54 55 56...
Страница 29: ...29 308876 Notes...