Graco 17H466 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 72

Graco 17H466 Скачать руководство пользователя страница 13

Hydraulic System Purging

3A3394E Repair - Parts

13

Hydraulic System
Purging

Follow this procedure after replacing any hydraulic
component other than the hydraulic gun manifold which
is self-purging.

1. Perform

Pressure Relief Procedure

2. Set LineStriper on blocks so wheels are off ground.

3. Fill oil reservoir to “Full” range.

4. Make sure drive wheel release is closed (+).

5. Start engine and run at low speed.

6. Turn on the Main Power Switch to engage clutch.

7. Slowly pull forward/reverse control lever in forward

and reverse directions 10 times.

NOTE:

Both rear wheels should turn in the correct

direction. If one wheel is not turning, carefully
restrain the spinning wheel to purge out the wheel
that is not turning.

This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury from
pressurized fluid, such as skin injection, splashing
fluid and moving parts, follow the Pressure Relief
Procedure when you stop dispensing and before
cleaning, checking, or servicing the equipment.

ti18587a

Full Range (cold)

ti343

1

a

+

ti18576a

ti23889a

ti23890a

ti23891a

«
...
11
12
13
14
15
...
»

Содержание 17H466









































































Отзывы:

Нет отзывов