Graco 1093, Руководство по эксплуатации и техническому обслуживанию

Страница: 29 / 30

Technical Data
313566J 29
Technical Data
NOTE: See your feed system manuals for dimensions, weights, and wetted parts lists for components. Dimensions,
weights, and wetted parts for combined assemblies and components not covered in your component feed system
manuals assemblies are listed below.
Motor Specifications
Any motor used with the motor driven model must meet
the following specifications.
Frame: NEMA 23
Torque at Typical Dispense Speed: 180 oz-in.
(11.25 in-lb) at 10 revolutions per second (1/2 in. rod
travel per second) or less. Above 10 revolutions per sec-
ond, the power declines.
Torque at Maximum Speed: 117 oz-in (7.3 in-lb) at 20
revolutions per second (1 in. of rod travel per second).
Motor Face Pilot Boss: 1.5 in. diameter by 0.0625 in.
projection from motor face flange.
Shaft Size: 0.25 diameter by 0.75 in. projection from
motor face pilot boss to end of shaft.
California Proposition 65
Maximum Ambient Temperature . . . . . . . . . . . . . . . . . . . 110°F (43°C)
Maximum Operating Temp. . . . . . . . . . . . . . . . . . . . . . . . 150°F (65°C)
Maximum Outlet Fluid Working Pressure. . . . . . . . . . . . . 2000 psi (14 MPa, 138 bar)
Maximum Air Working Pressure. . . . . . . . . . . . . . . . . . . . 100 psi (0.7 MPa, 7 bar)
Minimum Air Working Pressure . . . . . . . . . . . . . . . . . . . . 70 psi (480 kPa, 4.8 bar)
Maximum Material Inlet Pressure. . . . . . . . . . . . . . . . . . . Metal Sleeves: 1200 psi (8 MPa, 83 bar)
Plastic Sleeves: 400 psi (2.8 MPa, 28 bar)
Supplied Air Requirements. . . . . . . . . . . . . . . . . . . . . . . . 1 to 3 cfm at 80 psi to 100 psi
Shot Size Range (depending on metering rods selected) 0.193 cc to 14.479 cc
Maximum Cycle Rate (application dependent, heat
required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Up to 15 cycles per minute (with standard Graco motor)
Dimensions (H x L x W), height to end of material inlet
block (less needles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 in.: 14.35 x 8.375 x 1.75 in. (364 x 212 x 44 mm)
Graco-supplied Feed System Assemblies
(depends on selected options):
Smallest:
22.5 x 10 x 4 in. (572 x 254 x 102 mm)
Largest: 60 x 28 x 19 in. (1524 x 711 x 483 mm)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Metering Valve: 7 - 9 lb (3.17 - 4.08 kg)
with Standard Graco motor: 10-12 lb (4.55 - 5.44 kg)
Wetted Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Metering Valve: Hardened steel, 303/304, 404, UHM-
WPE, Tungsten, carbide, fluoroelastomer, EPDM,
PTFE
Graco-supplied Feed System Hoses and Fittings: Mild
steel, 303/304, PTFE, buna, polyethylene, polypropyl-
ene
Graco-supplied Tanks: Polyethylene, 303/304, mild steel
CALIFORNIA RESIDENTS
WARNING: Cancer and reproductive harm – www.P65warnings.ca.gov.