TAC 3
The TAC 3 is an
Auto On
, two-way signaling,
EVACUATE capable personal communicator. The TAC
3 provides automatic electronic accountability, trans-
mits emergency alarms, signals the status of the
unit and provides the ability to EVACUATE or call
back personnel as needed. The TAC 3 is designed to
compliment integrated PASS by providing additional
features and significant capability, without redun-
dancy. Through the utilization of TAC 3 and the T3
LCD Base or In-Command, Incident Commanders
are provided with the ability to EVACUATE or call-
back personnel as needed from dangerous situations.
The
Auto On
feature insures the TAC 3 is turned on
Automatically
when removed from a storage posi-
tion.
The TAC 3 is NOT an PASS DEVICE, But Per-
forms as an Automated Accountability and Two-
Way Emergency Signaling System.
TAC-3 Operating Instructions
When removed from a storage position, the TAC 3
Accountability Storage Key will automatically pop
off. When the TAC 3 turns
ON
, the operational signal
(an escalating series of loud attention getting audio
tones), will be heard accompanied by the visual wig-
wag display of two yellow LEDs. The yellow wig-wag
display indicates the TAC 3
unit is in the
ON
mode.
At the same time, the TAC 3 transceiver is also ac-
tivated and immediately starts signaling the T3 LCD
Base or In-Command.
While in the
ON
mode, the TAC 3 may be put into
ALARM
at any time by manually pressing the alarm
button located on the front surface of the unit. When
in
ALARM
, the yellow wig-wag display is replaced
by a rapid pulsing of two red LEDs accompanied
by a rapid modulated loud audio
Alarm Signal
.
When the TAC-3 is put into
ALARM
, an emergency
radio transmission is sent to the T3 LCD Base or In-
Command receiver. This alerts personnel outside the
immediate area that personnel may need assistance
Once in alarm, the unit can be reset or returned to
the
ON
mode by simply pressing both side buttons
simultaneously. To turn the TAC 3
OFF
replace the
Accountability Key and press both side buttons
simultaneously.
Always test TAC 3 with the T3 LCD
Base or In-Command to insure proper operation
before use.
TAC 3 EVACUATE
The TAC 3 EVACUATE function may be activated
by the Incident Commander from the T3 LCD Base
or In-Command at any time. The TAC 3
must
be in
the
ON
mode (accountability key removed) to re-
ceive EVACUATE signals. When the EVACUATE sig-
nal is received by the TAC 3, both amber LEDs flash
rapidly with a loud chirping audio alarm tone. The
EVACUATE alarm tone is easily differentiated from
other audio tones with minimal training.
When the EVACUATE alarm signal is received by
the TAC 3, it automatically sends an electronic
acknowledgement that the signal was received.
A manual acknowledgement of the EVACUATE sig-
nal is also required. Personnel manually acknowl-
edge the EVACUATE signal by momentarily press-
ing both side buttons simultaneously. The opera-
tional signal will be heard. This acknowledgement
will cause the flashing LEDs and the loud chirping
audio tones to cease. The manual acknowledgement
lets the Incident Commander know the signal was
received and understood. When personnel are out
of harms way and accounted for, the Incident
Commander can clear the EVACUATE field on the
In-Command.
“Auto-On” Activation
The TAC 3 is designed to be automatically put into
the
ON
mode or turned
ON
when removed from a
storage position, whether it is a seating position on
apparatus or a fixed storage position such as a gear
rack. When removed from the storage position, the
tether will tighten and the Accountability Storage Key
will automatically pop off putting the TAC 3 into the
ON
mode. At this point, the unit can be “reset” (from
the alarm to the
ON
mode) but cannot be turned
OFF
until the Accountability Storage Key is replaced
and both side buttons pressed simultaneously.
Snap hook attached to Transportation or Fixed Storage
Position.
Pull turnout gear away, the Tether tightens and pulls the
Accountability Key off the TAC 3. This will automatically
activate the TAC 3 into the Sensing Mode.
TAC 3
attached to
turnout gear
Snap
Hook
The Accountability Storage Key has an adjustable
tether for ease of use. The tether can be adjusted
from approx. 1’-6” to 3’ in length. This allows for easy
utilization whether you are anchoring the tether to a
transportation position (such as to a seat in a ve-
hicle) or a fixed storage position (such as in the fire
station). Accountability Storage Keys are available
with various length tethers to facilitate various op-
erational needs.
TAC 3 is designed to meet the design and perfor-
mance requirements for personal alert safety sys-
tems (PASS) to be used by personnel working alone
or engaged in other hazardous duities.
Plastic window
pops out. Remove
information and
replace with
information as desired.
Snap window back
in place.
Changing the identification
information in the
Accountability Storage
Key window
Push small screwdriver
through slot on inside
of key
An added benefit of the new Grace system is the
Accountability Storage Key. The clear Identification
Window located on the front of the key provides the
opportunity for specific identity of the TAC 3 user
through the ability to personalize keys with pictures,
names, numbers, dept. ID, bar-codes etc. The clear
access window easily snaps into place to protect
the enclosed information and provide instant ac-
cess for quick ID should the need arise. Informa-
tion in the Identification Window can easily be
changed by partially popping the ID window out with
a small, flat blade screwdriver through the access
slot located on the back side of the key.
To reduce the risk of ignition of a flammable
atmosphere, batteries must only be changed in an
area known to be non-flammable. To change the
battery, remove the four screws securing the back.
Remove the back cover, disconnect and dispose
of the spent battery and connect the new battery.
Replace the back cover and gently tighten all four
screws using a crisscross pattern for even gasket
pressure ensuring a good seal.
Do not over
tighten screws.
WARNING
Always use the specified 9 volt alka-
line battery. The Duracell MN 1604 is recommended
for optimum performance, as other batteries may
not provide the same operating life. Replacing the
battery every two to three months is required un-
less indicated sooner by the Low Battery Alarm.
The Low Battery Alarm will sound when the bat-
tery has been exhausted to 20% of capacity (indi-
cating approx. 1 hour operating time remains). Im-
mediate replacement of the battery is necessary
when the low battery alarm sounds.
The low battery alarm is an easily recognized
series of double audio beep tones enunciated ev-
ery five seconds when the TAC 3 is in the “ON” mode.
Grace Industries, Inc. assumes no liability for me-
chanical, electrical or other types of battery failure.
Warning - substitution of components may im-
pair intrinsic safety
.
Always test TAC 3 with the
T3 LCD Base or In-Command to insure proper
operation
after battery replacement.
Battery Installation/ Replacement
Safety Certifications
Intrinsically Safe per ANSI/UL-913 for Use in Class 1,
Div. 1, Groups A, B, C, and D Hazardous Locations.
Certified to CAN/CSA Std.C22.2 No. 157-92
Intrinsically Safe, Sécurité Intrinséque.
AVERTISEMENT: La Substitution De Composants
Peut Compromettre La Sécurité Intrinséque.
AVERTISEMENT: Afin De Prévenir L ‘Inflammation D’
Atmosphéres Dangereuses, NE Changer Les
Batteries Que Dans Des Emplacements Désignés
Non Dangereux.
CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate this equip-
ment.
Industry Canada Notices
This device has been designed to operate with an
antenna having a maximum gain of (1.5) dBi. An-
tenna having a higher gain is strictly prohibited per
regulations of Industry Canada. The required antenna
impedance is (50) ohms.
To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power
(EIRP) is not more than that required for successful
communication.
The installer of this radio equipment must ensure that
the antenna is located or pointed such that it does not
emit RF field in excess of Health Canada limits for the
general population; consault Safety Code 6, obtain-
able from Health Canada’s website www.hc-sc.gc.ca/
rpb
TAC 3 - Specifications
Dimensions:
2-1/8”" wide by 4-1/8" high
by 1-5/8" deep.
Weight:
Eight ounces with battery (w/out key).
Alarm Audio Output:
98+ dBA @ 10 feet.
Case:
Rugged, high temperature, impact resistant,
translucent, Orange polycarbonate. Entire case
glows during the
ON
and
Alarm
modes.
Methods of Attachment:
Rugged Grip Clip and D-ring for versatility in
attaching to gear.
Sound discernability:
6 dBA against given background noise.
Antenna:
Robust design which aids in signal propagation.
Threaded antenna for easy replacement.
Alarm Transmission:
A 1.5 second burst of RF transmissions
occurring every 4.5 seconds.
Range:
Dependent upon environmental conditions.
Battery:
Duracell MN 1604, 9 volt alkaline
recommended.
Battery Life:
Estimated at 100 hrs in
ON
mode and 2 to
4 hours in the Alarm mode.
