manualshive.com logo in svg

GPS Prueftechnik Digital Colour Analyzer, Руководство пользователя

Поделиться
Скачать
GPS Prueftechnik Digital Colour Analyzer Скачать руководство пользователя страница 10

 

02.11.2018 

 

10 

3. Setting the Digital Colour Analyzer  

After the software has been installed and the Digital Colour Analyzer has been attached the following settings have to be 
respected. 
 
Configuration: 
Interface 
The USB Port is configured as a virtual Com Port and will be designated a name such as Com5, Com6, etc. 
The  Baud Rate can be changed to any between 9600 and 115200 . 
Set the serial port to Auto and the baud rate to 115200. 

The Digital Colour Analyzer Test Program is a graphical tool that can be used to send commands and receive results 
from the Analyzer.  
One LED can be tested at a time. The results are stored in a data e.g. TestReport.txt.  
 
This program allows to determine the correct setting for the LED which has to be tested. 
For further details, please refer to chapter 3.3.3  . 
 
 
Alternately, a customised program may be generated that sends commands and receives data through the virtual 
USB Com Port or RS 232 interface. 

Figure 11: Settings 

Содержание Digital Colour Analyzer





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды