Goulds Pumps 3700i API610 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 126

background image

Current IOMs are available at

http://www.gouldspumps.com/en-us/tools

- and - resources/literature/

http://i-alert.com

or your local ITT Goulds Pumps Sales Rep.

Alarm mode

The condition monitor enters alarm mode when either vibration or temperature limits are exceeded over
two consecutive readings within a user defined period. Alarm mode is indicated with red flashing LED.

Table 4: Temperature and vibration limits

Variable

Limit

Temperature 100°C | 195°F Surface Temperature
Vibration

100% increase over the baseline level

Battery life

The i-ALERT®3 Condition Monitor battery is replaceable.

The battery life is not covered as part of the standard pump warranty.

This table shows the average condition monitor battery life under normal and alarm-mode operating con-
ditions.

Condition monitor operational state

Battery life

Normal operating and environmental conditions

Three to five years

Alarm mode

One year

3.3 Nameplate information

Important information for ordering

Every pump has a nameplate that provides information about the pump. The nameplate is located on the
pump casing.

When you order spare parts, identify this pump information:

•

Model

•

Size

•

Serial number

•

Item numbers of the required parts

Item numbers can be found in the spare parts list.

Refer to the nameplate on the pump casing for most of the information. See Parts List for item numbers.

Nameplate types

Nameplate

Description

Pump casing

Provides information about the hydraulic characteristics of the pump.

Pump

The formula for the pump size is: Discharge x Suction - Nominal Maximum Impeller Diameter in
inches.

(Example: 2x3-8)

ATEX

If applicable, your pump unit might have an ATEX nameplate affixed to the pump, the base-
plate, or the discharge head. The nameplate provides information about the ATEX specifica-
tions of this pump.

IECEx

If applicable, your pump unit might have the following IECEx nameplate affixed to the pump
and/or baseplate. The nameplate provides information about the IECEx specifications of this
pump.

3.3 Nameplate information

20

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

«
...
20
21
22
23
24
...
»

Содержание 3700i API610































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3700i API610

Бренд: Macnaught Страницы: 12

Бренд: A.O. Smith Страницы: 2

Бренд: ICP Страницы: 9

Бренд: Gardena Страницы: 16

Бренд: YUKEN KOGYO Страницы: 82

Бренд: Oerlikon Barmag Страницы: 36

Shurflo 8000 Series

Бренд: Lilie Страницы: 6

CLIMAGUARD TX23

Бренд: McLean Страницы: 20

ecoTOUGH NRC111-DV-LP

Бренд: Noritz Страницы: 32

RediHeat RH-120

Бренд: Spirax Sarco Страницы: 12

969-9365 Series

Бренд: Varian Страницы: 71

ProMax Garden 3500

Бренд: Oase Страницы: 201

Бренд: Drazice Страницы: 28

Бренд: Ultranatura Страницы: 24

EKHWS 150D3V3 Series

Бренд: Daikin Страницы: 20

Бренд: A.O. Smith Страницы: 32

Kempion PKD Series

Бренд: Cheonsei Страницы: 32

Бренд: Biral Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды