Gotting HG G-98820ZA Скачать руководство пользователя страница 27

Страница: 27 / 74

Components and Operation

HG G-98820ZA

English, Revision 09, Date: 13.12.2016

PDO_2 is transmitted with identifier 0x280 + node address. It contains 8 bytes accord-
ing to the following table.

The synchronous identifier is 0x80. It is possible to read out this parameter under index

[1005,00], but it is not possible to change it.

4.2.3.4.2

Heartbeat

The heartbeat mode is supported. Whenever a heartbeat time > 0 is set in the CAN

menu, the device status is transmitted under identifier (0x700 + node address) each

time the heartbeat timer has expired. The guard time is set to 0 afterwards.

4.2.3.4.3

Node Guarding

Whenever the Heartbeat time is set to 0, the device replies to a Remote Transmission

Request of the Identifier (0x700 + Node address) with the device status (refer to Table

14 above), while the highest bit changes. The device does not monitor the timely re-
ception of RTR Frames.

4.2.3.4.4

Description of the Service Data Objects (SDOs)

The service data opject is used to access to the object index. An SDO is always trans-
mitted with a confirmation, i. e. each reception of the message is acknowledged. The

identifiers for read and write access are:

Value

Variable

Value range

Comment

Sum Voltage

unsigned 16

0...1023

Voltage of the reference antenna coil

Dif Voltage

signed 16

0...±1023

Voltage of the positioning coil

Codes read

unsigned 8

0...255

Number of code readings

Voltage

unsigned 8

0...255

Operating voltage of the antenna [100 mV]

Power

unsigned 8

0...255

Power consumption of the antenna [10 mA]

Temperature

signed 8

-23...61

Board temperature [

Table 13

Variables of PDO_2

Node status

Code

stopped

0x04

preoperational

0x7f

operational

0x05

Table 14

Coding of the Node status

Read access

0x600 + Node address

Write access

0x580 + Node address

Table 15

Identifiers for read and write access

Содержание HG G-98820ZA











































































Результаты поиска

Содержание HG G-98820ZA

Отзывы:

Бренды по названию

Популярные бренды

Gotting HG G-98820ZA, Техническое описание

Результаты поиска

Содержание HG G-98820ZA

Отзывы:

Бренды по названию

Популярные бренды