background image

Device Description HG G-7335xZA English, Revision 05 | Date: 19.02.2020

47

Technical Data – Chapter 11

11

Technical Data

Table 55

Technical Data HG G-7335xZA

Technical Data HG G-7335xZA

Dimensions

160 mm x 90 mm x 50 mm

Weight

400 g

Protection class

IP 64

Relative humidity at 25

o

C 95% (without bedewing)

Operating temperature

0

o

C to +50

o

C

Storage temperature

-20

o

C to +70

o

C

Operating voltage

+24 V ±25%

Current consumption

approx. 100 mA

Input sensitivity

1 V

pp

 for 3/4 full range at rated frequency

Max. input voltage

5 V

pp

 (sum of all frequencies)

Output

CAN-Bus
HG G-73350

not electrically insulated
CANopen®, Device Profil DS 401
Node-ID and baud rate can be config

-

ured via the serial interface.
Terminating resistance is not inte

-

grated.

Profibus
HG G-73351

not electrically insulated
DP-V0 according to IEC61158/
EN50170
node ID and transmission rate can be 
configured via the serial interface.
Terminating resistance is not inte

-

grated.

Monitor serial 38400 baud, 8 data bits, parity even, 1 

stop bit, not electrically insulated

Update rate

10 ms

Frequency range

3 to 25 kHz (see Figure 14 on page 49)
X is compensated from 1 kHz to 28 kHz (see Figure 15 
on page 49)

Frequency switch

approx. 40 ms

band filter

>= 20

Содержание HG G-7335xZA Series





























































Отзывы: