analogue filters, Feed - Inside the g-RAY feedback loop, Gran - On the granulator/delay output - only the effected
signal is filtered, not the clean signal.
THE g-RAY FEEDBACK CIRCUIT
A new GotharMusic invention! It is actually a traditional feedback loop, with input taken from the analogue filters
output or the granulator/delay output, and then fed back into the analogue filters. The new thing is our g-RAY circuit. It
has 4 different positions. In position zero, it lets the feedback signal pass thru, and act like a traditional feedback circuit.
In position 1, 2 and 3 it creates more and more intermodulation of the feedback signal. In position 3, it creates sounds
that could remind of FM, but not exactly the same. It is also possible to place the digital filter inside the feedback loop,
to create filtered feedback sounds, and it's possible to boost, invert and delay the feedback signal, to create even more
unusual sounds. Feedback level and delay can be modulated.
THE GRANULATOR/DELAY
Anamono has a very flexible and fully programable granulator/delay section. In granulator mode, it cuts the input signal
up in a number of small fragments (from 1-128). It is then possible to program a fragment re-arrange sequence on up to
16 steps. Very useful for different sounding delay effects and for rearranging a beat or another kind of sequence in
realtime. Each granulator step can also be either time-stretched or pitch-shifted in realtime.
In delay mode, it acts as a traditional tape echo.
In both granulator and delay mode, it is possible to select the effect playback direction (forward / reverse), and it is also
possible to freeze the effected signal. When freezing, it stops recording the input signal, and plays back the content of
it's audio memory in a repeated loop. Can be used as a kind of loop-recorder. Maximum granulator/delay time are 1.5
second. Playback direction, freeze, time and mix can be modulated.
THE RING MODULATOR
Has a selection of 4 different input sources for each input, and 3 different output destinations. Input1 sources are:
Oscillator 1, external audio input, analogue filters and granulator/delay. Input2 sources are: Oscillator 2, LFO1,
analogue filters and granulator/delay. Output destinations are: Digital filter, analogue filters and VCA. Ringmodulator
output level can be modulated.
THE ANALOGUE VCA AND OVERDRIVE CIRCUIT
Anamono has a genuine analogue output stage VCA with added overdrive. The VCA (amp) output level is usually
controlled by the amp envelope, but a drone level is also included, to keep the output constantly open. An envelope
follower is also included, to make it possible for the signal present on the external audio input, to control the output
level. Any other modulation source can also be routed for additional output level control. The drive level of the crunchy
analogue overdrive circuit can likewise be controlled by any modulation source.
THE MODULATION SOURCES
All parameters in Anamono, that can be modulated, has a possible selection of 16 different modulation sources. They
are:
-Mod Envelope
: A traditional ADSR envelope. It has 2 sets of settings, that can be morphed between, using any
modulator.
-Squared Mod Envelope
: The output of the mod envelope turned into a square - When the mod envelope has a value
below half of it's max value, this will be zero. When the mod envelope reaches above it's half value, this will be at
maximum value.
-Modulator 1
: An 8 step very flexible modulator with a smooth output. Each step has a value parameter, a time
parameter (how long it will take to reach the next steps value), and a selection of, if it will continue, sustain or loop,
after this step. It has a flexible trigger system: Off (freerun, no triggering), Key-reset (key triggered without re-
triggering), Key-trigger (key triggered with re-triggering), Key'ed (advances one step, every time a note-on is
received), Play (the play/enter knob starts and stops the modulator) and MIDI (synced to MIDI). It has 2 sets of settings,
that can be morphed between, using any modulator.
-Stepped Modulator 1
: Modulator 1 stepped output. Every time modulator 1 reaches a new step/value this is updated.
This can also be set up to put out note and gate values, and used as a morphable step-sequencer.
-Modulator 2
: A 5-step shapable modulator. Step 1: delay time, step 2: rise time to full value, step 3: hold time at full
value, step 4: fall time to zero, step 5: hold time at zero value. Can be key-triggered, looped or key-triggered and
looped. It has 2 sets of settings, that can be morphed between, using any modulator.
