Gossen MetraWatt SECUTEST SII Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 48

background image

22

GOSSEN METRAWATT GMBH

9.6

Alternating / Direct Voltage U

AC/DC

– Max. 253 V (feature F01)

Direct, alternating and pulsating voltages of up to 253 V can be measured
between the N (2) and L (3) connector jacks.

Select the

U

AC/DC

measurement and start.

9.7

Resistance R (feature F01)

Resistance of up to 150 k

Ω

can be measured between the PE (1) and N

(2) connector jacks.

Select the

R

measurement and start.

9.8

Measurements with Accessories (feature F01)

9.8.1

Alternating Current I

Z

with Clip-On Transformer (feature F01)

Connection

Alternating current can be measured in two measuring ranges
(1 mA

…

10 A ~, 1 A

…

100 A~) with a clip-on current-voltage

transformer connected to the N (2) and L (3) jacks (e.g. the WZ12C).

Start the

I

Z

measurement.

Select measuring range.

«
...
20
21
22
23
24
...
»

Содержание SECUTEST SII

















































Отзывы:

Нет отзывов

Похожие инструкции для SECUTEST SII

Бренд: Palazzetti Страницы: 112

Бренд: NEC Страницы: 44

Бренд: Quincy lab Страницы: 4

Бренд: Campbell Страницы: 2

Бренд: XM Fitness Страницы: 10

Бренд: UNI-T Страницы: 4

UPO3000E Series

Бренд: UNI-T Страницы: 94

Бренд: Underhill Страницы: 12

Бренд: UMS Страницы: 92

Бренд: Yamaha Страницы: 5

Бренд: YOKOGAWA Страницы: 75

Бренд: Sable Страницы: 28

Biosafe 110 Port

Бренд: Sartorius Страницы: 2

Бренд: Tarter Страницы: 18

Бренд: laerdal Страницы: 40

Бренд: Jumper Страницы: 12

Бренд: SMC Networks Страницы: 2

Бренд: Laserworld Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды