Gorilla Treasure Trove II Скачать руководство пользователя страница 63

Страница: 63 / 103

3) TIE THESE THREE KNOTS BELOW THE ROPE LADDER

A PEN.

THE LEFT FRONT SIDE OF THE FORT LOOKING AT IT.

BELOW THE ROPE LADDER SUPPORT.

RUNG.

SUPPORT AND TIE 3 KNOTS. THE BOTTOM OF EACH KNOT SHOULD BE 6"

2.1) SLIDE A ROPE LADDER RUNG AGAINST THE THREE KNOTS.

ROPE LADDER SUPPORT

THIS IS THE VIEW AS IF YOU WERE STANDING AT

7) TIE KNOTS ON BACK SIDE OF ROPE LADDER RUNNER

RUNG AND PLACE TAPE ON THE ROPE OR MARK WITH

2) MEASURE DOWN 6" BELOW THE BOTTOM OF THE ROPE LADDER

ROPE LADDER RUNNER

5) SLIDE THE NEXT ROPE LADDER RUNG UP TO THE MARKS

OR TAPE. TIE THREE KNOTS UNDER THE ROPE LADDER RUNG.

4) MEASURE DOWN 10-5/8" BELOW THE ROPE LADDER

1) TIE A KNOT IN EACH ROPE AND THREAD THEM THROUGH

THE BACK SIDE OF THE ROPE LADDER SUPPORT.

10 58 "

LADDER RUNNER AND RETIE IT UNTIL YOU CAN NO LONGER WRAP THE ROPE AROUND YOUR HAND.

1: FIND THREE ROPE LADDER ROPES. MAKE A KNOT IN THE END OF EACH ROPE AND THREAD THE FREE END

THROUGH THE BACK SIDE OF THE ROPE LADDER SUPPORT. PULL EACH ROPE TAUGHT.

2: MEASURE DOWN FROM THE BOTTOM OF THE ROPE LADDER SUPPORT 6 INCHES AND TIE A KNOT. THE

BOTTOM OF THE KNOT SHOULD BE 6 INCHES BELOW THE ROPE LADDER SUPPORT. SLIDE EACH ROPE

THROUGH THE HOLES IN ONE ROPE LADDER RUNG. SLIDE THE RUNG UP AGAINST THE BOTTOM OF THE

KNOTS.

3: TIE THREE KNOTS BELOW THE ROPE LADDER RUNG.

4: MEASURE DOWN FROM THE BOTTOM OF THE ROPE LADDER RUNG 10-5/8 INCHES AND MAKE A MARK ON

THE ROPE WITH A PIECE OF TAPE OR A MARKER. THREAD ANOTHER ROPE LADDER RUNG ONTO THE ROPES.

5: WITH THE TOP OF THE RUNG EVEN WITH THE 10-5/8 INCH MARK TIE THREE KNOTS BELOW THE SECOND

ROPE LADDER RUNG.

6: REPEAT SUBSTEPS 4-5 FOR THE REMAINING ROPE LADDER RUNGS.

7: THREAD THE BOTTOM END OF EACH ROPE THROUGH THE HOLES IN THE ROPE LADDER RUNNER AND TIE

THEM OFF. GRAB EACH EACH ROPE AND ATTEMPT TO WRAP IT AROUND YOUR HAND. IF THE ROPE WRAPS

AROUND YOUR HAND IT IS TOO LOOSE. IF THE ROPE IS TOO LOOSE UNTIE THE KNOT BEHIND THE ROPE

6) REPEAT 4 & 5 FOR REMAINING ROPE LADDER RUNGS.

STEP 63: ROPE LADDER

108

Содержание Treasure Trove II








































































































Результаты поиска

Содержание Treasure Trove II

Отзывы:

Похожие инструкции для Treasure Trove II

Бренды по названию

Популярные бренды

Gorilla Treasure Trove II, Инструкция по сборке

Результаты поиска

Содержание Treasure Trove II

Отзывы:

Похожие инструкции для Treasure Trove II

Бренды по названию

Популярные бренды