Gorilla Playsets Riverview 801N Скачать руководство пользователя страница 95

Страница: 95 / 116

FRONT TOP PANEL

BOTTOM ROCK WALL BOARD

DRILL 7/8" HOLE IN

BOARD.

YOU MAY

TIE UP TO 3

KNOTS TO

AID IN

CLIMBING

SPACED

ABOUT 18"

APART.

NOW ATTEMPT TO WRAP THE ROPE AROUND YOUR HAND. IF THE ROPE WRAPS AROUND YOUR HAND IT IS TOO

LOOSE. UNTIE ONE END AND THEN RE-TIE IT UNTIL IT NO LONGER WRAPS AROUND YOUR HAND.

1:DRILL A 7/8" HOLE THROUGH THE FRONT TOP PANEL BOARD (ABOVE THE ROCK WALL) FOR THE CLIMBING ROPE.

TIP: PLACE A SCRAP 2 X 4 OR 4 X 4 BLOCK BEHIND THE BACK SIDE OF WHERE THE HOLE IS GOING TO BE DRILLED.

THIS SHOULD HELP TO PREVENT SPLITOUT ON THE BACK SIDE.

DO NOT PLACE YOUR HAND DIRECTLY BEHIND THE

DRILL BIT WHEN DRILLING THE HOLE OR INJURY MAY OCCUR.

2: TIE A KNOT AT ONE END OF THE 10' ROPE AND THREAD IT THROUGH THE HOLE IN THE FRONT TOP PANEL BOARD.

3: YOU CAN TIE A FEW (NO MORE THAN THREE) KNOTS IN THE ROPE TO AID IN CLIMBING APPROXIMATELY 18"

APART BEFORE TYING THE KNOT BEHIND THE BOTTOM ROCK WALL BOARD.

4: THE UNTIED END WILL GO THROUGH THE HOLE OF THE BOTTOM ROCK WALL BOARD. TIE A SECURE KNOT AT THE

END MAKING SURE THAT THE ROPE IS TIGHT AND WILL NOT WRAP AROUND YOUR HAND.

HINT: TO REDUCE THE AMOUNT OF SLACK IN THE ROPE, LIFT THE ROCK WALL ASSEMBLY SLIGHTLY WHEN TYING THE

KNOT IN THE BOTTOM ROCK WALL BOARD. WHEN YOU LOWER THE ASSEMBLY, THE ROPE WILL TIGHTEN.

STEP 54: INSTALLING THE CLIMBING ROPE

Содержание Riverview 801N





















































































































Результаты поиска

Содержание Riverview 801N

Отзывы:

Бренды по названию

Популярные бренды

Gorilla Playsets Riverview 801N, Руководство пользователя

Результаты поиска

Содержание Riverview 801N

Отзывы:

Бренды по названию

Популярные бренды