manualshive.com logo in svg

Gorilla Playsets 1500BW, Руководство пользователя, Страница: 49 / 124

Поделиться
Скачать
Gorilla Playsets 1500BW Скачать руководство пользователя страница 49

STEP 6: REAR FRAME ASSEMBLY

1: PLACE THE 2 X 6 X 70" SANDBOX BOARD ON THE BOTTOM REAR OF THE CORNER POSTS. THE HOLES IN THE 

SANDBOX BOARD MUST BE OFFSET UP.
2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO THE

T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.
3: PLACE THE 2 X 6 X 70" BOTTOM PANEL BOARD AT THE MIDDLE OF THE REAR CORNER POSTS. THE HOLES IN

THE BOTTOM PANEL BOARD MUST BE OFFSET UP.
4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE BOTTOM PANEL BOARD

TO THE T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.
5: PLACE THE 2 X 4 X 70" REAR TOP PANEL BOARD NEAR THE TOP OF THE REAR CORNER POSTS. THE HOLES IN THE TOP 

PANEL BOARD MUST BE OFFSET UP.
6: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE HOLES OF THE TOP PANEL BOARD TO

THE T-NUTS INSTALLED ON THE CORNER POSTS.

SANDBOX BOARD

OFFSET HOLES UP

5/16" WASHER

HEX BOLT

2 X 4 X 70"

REAR TOP PANEL BOARD

OFFSET HOLES UP

2 X 6 X 70"

OFFSET HOLES UP

BOTTOM PANEL BOARD

2 X 6 X 70"

5/16 X 4-1/2"

REAR OF FORT

41

Содержание 1500BW





























































































































Отзывы:

Нет отзывов