Gorilla Playsets 1150 Скачать руководство пользователя страница 69

Страница: 69 / 80

1) TIE A "FIGURE 8" KNOT IN EACH ROPE AND

15"

THREAD THEM THROUGH THE BACK SIDE OF THE

2.1) SLIDE A ROPE LADDER STEP AGAINST THE TWO KNOTS.

ROPE LADDER SUPPORT.

THIS VIEW IS AS IF YOU ARE STANDING IN FRONT OF THE LADDER STEPS

2 X 4 X 19" ROPE LADDER STEP 1150V

11"

SPACING

6) TIE THUMB KNOTS ON BACK SIDE OF ROPE LADDER RUNNER.

3) TIE THESE TWO THUMB KNOTS BELOW THE ROPE LADDER STEP.

2) MEASURE DOWN 15" BELOW THE BOTTOM OF THE ROPE LADDER

SUPPORT AND TIE 2 THUMB KNOTS. THE TOP OF EACH KNOT SHOULD

LIE AT THE 15" MARK.

STEP 35: ROPE LADDER

1: MAKE A FIGURE 8 KNOT IN THE END OF EACH ROPE AND THREAD THE FREE END THROUGH THE BACK SIDE OF THE

ROPE LADDER SUPPORT. PULL EACH ROPE TAUT.

2: MEASURE FROM THE BOTTOM OF THE ROPE LADDER SUPPORT DOWN 15 INCHES AND TIE A THUMB KNOT. THE

TOP OF THE KNOT SHOULD BE 15 INCHES BELOW THE BOTTOM OF THE ROPE LADDER SUPPORT. SLIDE EACH ROPE

THROUGH THE HOLES IN ONE ROPE LADDER STEP. SLIDE THE STEP UP AGAINST THE BOTTOM OF THE KNOTS.

3: TIE TWO THUMB KNOTS BELOW THE ROPE LADDER STEP.

4: SPACE THE ROPE LADDER STEPS 11 INCHES APART. TIE TWO GRANNY KNOTS BELOW THE SECOND LADDER STEP.

5: REPEAT SUBSTEP 4 FOR THE REMAINING LADDER STEPS.

6: THREAD ROPES THROUGH THE HOLES IN THE ROPE LADDER RUNNER AND TIE A GRANNY KNOT. GRAB EACH

ROPE AND ATTEMPT TO WRAP IT AROUND YOUR HAND. IF THE ROPE WRAPS AROUND YOUR HAND IT IS TOO

LOOSE. IF THE ROPE IS TOO LOOSE UNTIE THE KNOT BEHIND THE ROPE LADDER RUNNER AND RETIE IT UNTIL YOU

CAN NO LONGER WRAP THE ROPE AROUND YOUR HAND. TIE GRANNY KNOTS IN THE ROPE UNTIL ALL OF IT IS USED.

Содержание 1150

















































































Результаты поиска

Содержание 1150

Отзывы:

Похожие инструкции для 1150

Бренды по названию

Популярные бренды

Gorilla Playsets 1150, Руководство пользователя

Результаты поиска

Содержание 1150

Отзывы:

Похожие инструкции для 1150

Бренды по названию

Популярные бренды